
Overview
Diffused Lens Cover for LBFA LuxBar series Light Fixtures. Available in 5.9in (15cm), 11.8in (30cm), 23.6in (60cm), 35.4in (90cm), 47.2in (120cm) lengths. This adhesive lens cover can be easily applied to the existing lens.
We offer a range of LuxBar specific mounting and wiring options to meet a large range of needs. This flexible system of mountings clips, cables, and connectors will allow you all the flexibility you need to get the most from your Linear Light Bar Fixture.



Product | Option | Part Number |
1. Direct Connect Jumper | - | LBFA-I |
2. LuxBar Interconnect Jumper | 9.8in (25cm) | LBFA-I25 |
19.7in (50cm) | LBFA-I50 | |
39.4in (100cm) | LBFA-I100 | |
59.1in (150cm) | LBFA-I150 | |
72.1in (183cm) | LBFA-I183 | |
3. Right Angle Jumper | - | LBFA-IU |
4. LuxBar Power Connectors | 11.8in (30cm) Flat Pin | LBFA-P30 |
19.7in (50cm) Right Angle | LBFA-PRA30 | |
19.7in (50cm) Flat Pin | LBFA-P50 | |
39.4in (100cm) Flat Pin | LBFA-P100 | |
5. LuxBar Pigtail Power Connector | - | LBFA-PPT |
6. LuxBar Power Switches, 11.8in (30cm) Straight Plug | - | LBFA-SW30 |
7. LuxBar Power Switches, 72.1in (183cm) Right Angle Plug | - | LBFA-SW183 |
8. Cable Joiner for Interconnect Jumpers | Cable to Cable Joiner | LBFA-JCC |
Multiple Interconnect Cable Joiner | LBFA-MCJ | |
9. Flat Type Mounting Clip (including screw) | - | LBFA-MC1 |
10. Angled Type Mounting Clip (including screw) | - | LBFA-MC2 |
11. Aimable Clip Mounting Clip (including screw) | - | LBFA-MC3 |
12. Bar to Bar Back Clip | - | LBFA-BC1 |
13. LuxBar Diffused Lens Cover | 15cm(5.9in) | LB-DF-L142 |
30cm(11.8in) | LB-DF-L288 | |
60cm(23.6in) | LB-DF-L588 | |
90cm(35.5in) | LB-DF-L888 | |
120cm(47.2in) | LB-DF-L1188 | |
14. LuxBar PIR Motion Sensor | - | LBFA-PIR |
Specifications
Accessories

Reviews
Overall Rating
Total Reviews
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
Sticks on to the clear lens, doesn't replace it
The Luxbars come with a clear plastic lens already installed. This diffuser comes with adhesive on one side; it sticks *on top of* the lens that is already there, instead of replacing it. This works OK; it's just not apparent from the pictures on the site. It also means that you can't easily go back to the clear lens only if you decide you don't like the diffuser.
Pleased with results
I used several of these lens covers in multiple lengths. They are approximately 1 mm thick and stiff enough to easily align and apply. Each one was about 1/4 inch too long, but simple to cut to exact length with a utility knife. I like how bright the LED strips are, so initially I was concerned these diffusers would reduce the light too much, however that is not a problem, the overall light output is essentially the same. These were installed on under-cabinet lights, so it remains to be seen if the adhesive will stand the tests of gravity and time.
Great under the counter / cabinet LED
There are only two improvements I suggest: 1) include a on/off switch (inline or not) and 2) improve the power connector plug so as the prongs are not so delicate. I’d also like to recommend Super Bright LEDs it is a very good company to do business with!
Didn’t fit..Can’t use
It has an adhesive strip which is supposed simply attach to the lens cover of the light bar. Unfortunately, the rigid plastic cover was about 3/16” too long and 1/16” too wide...and I have no way to shave it down to fit. The Tech-Service people are checking their stock to see if this is a recurring problem. I’m sure Superbright will make it right. It is just frustrating!