4" LED Truck and Trailer Turn Signal and Parking Light - Built-In Flange - 3-Pin Connector - Flush Mount - 12 LEDs
Part Number
STFM-x12P
Overview
Designed to accept industry standard 3-pin plugs, this 4” round LED light meets DOT FMVSS 108 requirements for use as parking lights, turn signal lights, hazard warning lights, brake lights, and tail lights. The light mounts flush with the built-in plastic 3-hole mounting flange. Each light boasts 12 high-flux LEDs that operate with in a wide 9-14.8V DC range and consumes 90% less energy than incandescent lamps. Sonically sealed polycarbonate lens and weatherproof housing. The truck/trailer lights are available in amber, red, or white; white lamps are single intensity. Lifetime warranty on all truck/trailer lights.
In order for certain products within controlled categories, such as electrical and electronic devices, to be legally sold in the European Economic Area, they must bear a CE label, which stands for Conformité Européenne (European Conformity). Products with this label meet environmental, health, and safety standards put into place by European legislation.
The Department of Transportation (DOT) sets strict guidelines in respect to external vehicle lighting that must be followed in order for a light to be street legal. Vehicle fixtures—such as headlights and taillights—that have a DOT compliance mark are legal, safe, and considered to provide suitable illumination for street use when properly installed.
Super Bright LEDs, Inc. warrants that products carrying a lifetime warranty will be free from defects in the material and workmanship for the lifetime of the product. If Super Bright LEDs verifies that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product with the same product. In the case the exact product is no longer available, a gift card for the value of the original purchase price will be provided. Read More
Applications
- Turn Lights
- Tail Lights
- Reverse Lights
- Brake Lights
- Trucks
- Hazard Lights
- Trailer Lights
- RV Lights
- LED Boat Lights
- Parking Lights
Similar Round Tail Lamps
| Color Options | DOT/SAE ID Code | Mount Type | Price | ||
|
Amber
Red
|
|
Flange
|
$5.99 - $6.49
ea.
|
|
|
White
|
|
Flange
|
$13.99
ea.
|
|
|
Amber
Red
|
|
Flange
|
$12.99
ea.
|
|
|
White
|
|
Flange
|
$14.99
ea.
|
|
|
Red
|
|
Flange
|
$16.99
ea.
|
|
|
Amber
Red
|
|
Flange
|
$24.99
ea.
|
|
|
Amber
Red
|
|
Flange
|
$24.99
ea.
|
|
Specifications
| DOT Standard | FMVSS 108 |
|---|---|
| IP Rating | IP65 |
| Mount Type | Flange |
| Standards And Certifications | CE, DOT Compliant |
| Voltage | 9-14.8 VDC |
| PC Rated | No |
.
Swipe left to see additional specifications
| Part NO | Current Draw Current Draw |
|---|---|
| STFM-A12P | 0.21A (210mA), 0.04A (40mA) |
| STFM-R12P | 0.18A (180mA), 0.04A (40mA) |
| STFM-W12P | 0.19A (190mA) |
Accessories & Power Supplies
Accessories Links
Accessory Category-
$2.49 ea.Right Angle 3-Wire Pigtail for Trailer Lights - 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3RIn stockDesigned for ST, PT, and RT series truck lights and trailer lights, the right angle 3-pin plug features 10 inch wires allowing for easy installation. -
$0.45 ea.22-12 AWG Waterproof Silicone Filled Twist-On Wire Connector Part Number: WWN-2212In stockUL listed waterproof wire connectors suitable for all wire splices, especially those exposed to condensation, water, vapors or dust. 22-12 AWG Blue wire connector pre-filled with silicone to seal and protect connection from moisture. Not suitable for submersed connections. Price for each. -
$5.99 ea.Brake Light Strobe Module - Brake Light Strobe Module Part Number: LSC-100AIn stockBrake light strobe module works with LED brake or reverse lights. Strobe module rapidly flashes bulbs 4 times for 0.4 seconds, slowly 4 times for 2.6 seconds, and then lights remain on bright until brake pedal is released. 12V DC Operation with a maximum load of 1.25 amps. Weather-resistant housing easily mounts to vehicle with double-sided adhesive. Includes 6” power wires. -
$0.19 ea.Corrugated Split Loom Part Number: CSL-xIn stockCSL-x series black polyethylene corrugated split looms. Protects and conceal wires, cables, and tubings. Splits down the side to allow covering of pre-installed wiring. Corrugated split looms are available in 1/4", 3/8", 1/2", and 3/4" sizes. -
$9.95 ea.Weatherproof Dolphin Super B Connector with Sealant - 100 Pieces Part Number: DC-x-SIn stockDolphin Super B Connectors provide the industry’s most reliable connection with their unique design and tine structure. They reduce costs, will not corrode and do not require insulation stripping of most wire gauges before insertion. Weatherproof IP65 rating. Available in a 100 Pack.
-
$2.99 ea.Waterproof Mini Automotive Fuse Holder - Waterproof Part Number: WMFHIn stockFuse Holder with Waterproof Cap and pigtail wires. Takes blade-mounting Mini fuses sold separately above- 12 Gauge 4" wire leads. Price for each. -
$5.99 ea.Pulsing Strobe Module - Pulsing Strobe Module Part Number: LSC-100BIn stockThis pulsing strobe module produces a continuous flash that is perfect for vehicle LED warning lights or hazard lights. 12V DC Operation with a maximum load of 1.25 amps. Weather-resistant housing easily mounts to vehicle with double-sided adhesive. Includes 6” power wires. Price per strobe module. -
$0.23 ea.16-14 AWG Butt Connectors - Butt Connectors Part Number: PSC-164In stockUse this butt connector to connect and seal 16-14 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun. -
$11.99 ea.MSC2-24W LED Multi-function Strobe Controller - LED Strobe Controller Part Number: MSC2-24WIn stockMulti-Function Strobe Controller with right and left outputs and 10 alternating dynamic strobe modes. LED indicator lights on controller demonstrate the mode selected. Power-cycle mode retention allows your light to return to the mode that was selected before it was powered off. Use for LED emergency, warning and hazard lights. 12-24VDC operation. 2 Amp max load. Mount using included double-sided adhesive. Price per unit -
$19.99 ea.Strobe Light Controller with Wireless Key Fob Remote - Dual 24W Outputs - 16 Strobe Patterns Part Number: LMC-700AIn stockTurn any 12V work or vehicle light into a strobe light with LMC series Strobe Light Controller. Convenient Key Fob RF Remote controls lights wirelessly. Power button turns lights on, while UP arrow selects constant ON, and DOWN arrow cycles through 16 unique strobe patterns. Dual output allows 2 lights of up to 24-watts each to be controlled, with flash patterns that either alternate between the lights or strobe simultaneously. Memory feature turns light on in the last mode that was being used. Use this strobe controller to give extra control and safety to emergency and first responder vehicles, work lights, and more. Sturdy plastic construction resists water ingress. -
$0.25 ea.Automotive Mini Blade Fuses Part Number: MAF-xIn stockMiniature blade-mounting automotive fuses. Select from 2 Amp to 30 Amp fuse. Price for each however bulk discounts are available. -
$4.49 ea.Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Pin PL-3 Plug - 10" Long Part Number: A47PBIn stockTo connect an LED truck and trailer lights with a PL-3 connector to power, use the 3-wire pigtail connector. 10" right angle pigtail wire leads with stripped ends.
-
View all
All Accessories1 additional compatible accessories
-
$2.49 ea.Right Angle 3-Wire Pigtail for Trailer Lights - 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3RIn stockDesigned for ST, PT, and RT series truck lights and trailer lights, the right angle 3-pin plug features 10 inch wires allowing for easy installation.
-
$4.49 ea.Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Pin PL-3 Plug - 10" Long Part Number: A47PBIn stock
To connect an LED truck and trailer lights with a PL-3 connector to power, use the 3-wire pigtail connector. 10" right angle pigtail wire leads with stripped ends.
-
$2.49 ea.3-Wire Pigtail for Trailer Lights - 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3SIn stockDesigned for ST, PT, and RT series truck lights and trailer lights, the straight 3-pin plug features 10 inch wires allowing for easy installation. -
$3.99 ea.3-Wire Pigtail for Optronics Trailer Lights - 3-Pin PL-3 Plug - 10" Long Part Number: A45PBIn stockTo connect an LED truck and trailer lights with a PL-3 connector to power, use the 3-wire pigtail connector. 10" straight pigtail wire leads with stripped ends.
-
$4.49 ea.3-Wire Pigtail for Peterson Trailer Lights - 3 Pin PL-3 Plug - 10-1/2" Long Part Number: B431-491In stockHardwire LED truck and trailer lights to power using the 3-wire PL-3 pigtail harness. Stripped hot wires and ground wire with ring terminal. Molded plug for single or double contact.
-
$4.99 ea.Right Angle 3-Wire Pigtail for Peterson Trailer Lights - 3 Pin PL-3 Plug - 10-1/2" Long Part Number: B421-491In stockHardwire LED truck and trailer lights to power using the 3-wire PL-3 pigtail harness. Stripped hot wires and ground wire with ring terminal. Right angle plug for single or double contact.
-
$0.45 ea.22-12 AWG Waterproof Silicone Filled Twist-On Wire Connector Part Number: WWN-2212In stockUL listed waterproof wire connectors suitable for all wire splices, especially those exposed to condensation, water, vapors or dust. 22-12 AWG Blue wire connector pre-filled with silicone to seal and protect connection from moisture. Not suitable for submersed connections. Price for each.
-
$0.19 ea.Corrugated Split Loom Part Number: CSL-xIn stockCSL-x series black polyethylene corrugated split looms. Protects and conceal wires, cables, and tubings. Splits down the side to allow covering of pre-installed wiring. Corrugated split looms are available in 1/4", 3/8", 1/2", and 3/4" sizes. -
$9.95 ea.Weatherproof Dolphin Super B Connector with Sealant - 100 Pieces Part Number: DC-x-SIn stockDolphin Super B Connectors provide the industry’s most reliable connection with their unique design and tine structure. They reduce costs, will not corrode and do not require insulation stripping of most wire gauges before insertion. Weatherproof IP65 rating. Available in a 100 Pack.
-
$0.23 ea.16-14 AWG Butt Connectors - Butt Connectors Part Number: PSC-164In stockUse this butt connector to connect and seal 16-14 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun.
-
$0.39 ea.Black Cable Ties - 10 Pack Part Number: CT-B-10In stock4, 6, and 11 inch Cable tie - .875" max dia.; 6 inch Cable tie - 1.50" max dia.; 11 inch Cable tie with - 3.062" max dia.; 16 inch Stud Mount Cable tie - 4.125" max dia. -
$0.15 ea.Hole Snap-In Strain Relief Bushing Part Number: PSB-xIn stockEliminates sharp edges and protects wires and harnesses passing through holes in metal plates and panels. Resists up to 35 pounds pull. -
$1.99 ea.Dielectric Electrical Connector Grease - 4 Grams Part Number: CP-1In stockHigh performance silicone based dielectric grease that can be applied to any electrical connection to keep out moisture and prevent corrosion. Use with connectors, sockets, pigtails, trailer connections, headlight/taillight bulb bases, contacts, etc. Includes (1) 0.14-ounce packet. -
$0.99 per Foot4-Wire Trailer Wire - 16 Gauge Parallel Bonded Wire - Four Conductor - 16 AWG Power Wire Part Number: WP16-4In stockThis 4-wire trailer wiring is for low voltage installations. Parallel bonded four conductor 16 gauge 1x16 stranded wire. Commonly used for trailer wiring. Price per foot. -
$0.69 ea.Nylon Push Mount Base for Cable Ties - Push Mount Part Number: PMB-250In stockCable tie mounting base to secure wires on surface. Fits 1/4" diameter hole - For ties up to 3/8" wide. -
$1.99 ea.Heavy Duty Mount for Cable Ties Part Number: HDM-xIn stockHeavy-duty mount for cable ties to secure wires to surfaces up to 1/2" wide. A small tab inside the mounting hole temporarily engages threads, allowing assemblers to pre-install the mount on a stud before securing it with a washer and nut (not included). Available in #10 size mounting hole (1/4") and #8 size mounting hole (3/16"). Price for each.
-
$5.99 ea.Brake Light Strobe Module - Brake Light Strobe Module Part Number: LSC-100AIn stockBrake light strobe module works with LED brake or reverse lights. Strobe module rapidly flashes bulbs 4 times for 0.4 seconds, slowly 4 times for 2.6 seconds, and then lights remain on bright until brake pedal is released. 12V DC Operation with a maximum load of 1.25 amps. Weather-resistant housing easily mounts to vehicle with double-sided adhesive. Includes 6” power wires.
-
$2.99 ea.Waterproof Mini Automotive Fuse Holder - Waterproof Part Number: WMFHIn stockFuse Holder with Waterproof Cap and pigtail wires. Takes blade-mounting Mini fuses sold separately above- 12 Gauge 4" wire leads. Price for each.
-
$5.99 ea.Pulsing Strobe Module - Pulsing Strobe Module Part Number: LSC-100BIn stockThis pulsing strobe module produces a continuous flash that is perfect for vehicle LED warning lights or hazard lights. 12V DC Operation with a maximum load of 1.25 amps. Weather-resistant housing easily mounts to vehicle with double-sided adhesive. Includes 6” power wires. Price per strobe module.
-
$11.99 ea.MSC2-24W LED Multi-function Strobe Controller - LED Strobe Controller Part Number: MSC2-24WIn stockMulti-Function Strobe Controller with right and left outputs and 10 alternating dynamic strobe modes. LED indicator lights on controller demonstrate the mode selected. Power-cycle mode retention allows your light to return to the mode that was selected before it was powered off. Use for LED emergency, warning and hazard lights. 12-24VDC operation. 2 Amp max load. Mount using included double-sided adhesive. Price per unit
-
$19.99 ea.Strobe Light Controller with Wireless Key Fob Remote - Dual 24W Outputs - 16 Strobe Patterns Part Number: LMC-700AIn stockTurn any 12V work or vehicle light into a strobe light with LMC series Strobe Light Controller. Convenient Key Fob RF Remote controls lights wirelessly. Power button turns lights on, while UP arrow selects constant ON, and DOWN arrow cycles through 16 unique strobe patterns. Dual output allows 2 lights of up to 24-watts each to be controlled, with flash patterns that either alternate between the lights or strobe simultaneously. Memory feature turns light on in the last mode that was being used. Use this strobe controller to give extra control and safety to emergency and first responder vehicles, work lights, and more. Sturdy plastic construction resists water ingress.
-
$0.25 ea.Automotive Mini Blade Fuses Part Number: MAF-xIn stockMiniature blade-mounting automotive fuses. Select from 2 Amp to 30 Amp fuse. Price for each however bulk discounts are available. -
$39.99 ea.SHO-ME Solid State Strobe LED Flasher - LED Flasher Part Number: 11.1005.SFIn stockUse the SHO-ME heavy-duty LED strobe flasher on any emergency vehicle. This flasher features 7 selectable strobe flash patterns and is compatible with most LED lights. 12V DC operation with a maximum load of 3 amps per channel. The water-resistant housing is fully potted for protection against vibration and shock. Includes 17-1/2" power wires.
-
$2.49 ea.Right Angle 3-Wire Pigtail for Trailer Lights - 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3RIn stockDesigned for ST, PT, and RT series truck lights and trailer lights, the right angle 3-pin plug features 10 inch wires allowing for easy installation.
-
$2.49 ea.3-Wire Pigtail for Trailer Lights - 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3SIn stockDesigned for ST, PT, and RT series truck lights and trailer lights, the straight 3-pin plug features 10 inch wires allowing for easy installation.
Reviews
3.7 / 5 stars
11 reviews
3.7 / 5 stars
11 reviews
Write Your Own Review
Review Guidelines
superbrightleds.com reads and approves all reviews before listing them on the website. Below you will find a list of reasons that can result in your review being rejected.
- Review text does not pertain to the product
- Abusive and offensive language
- Photos are not related to the reviewed product
- Any violation of laws and/or copyrighted material
- Unrelated hyperlinks/URLs
Stay in touch & Save 10% on your next order!*