Triangle LED Turn Signal Light for Peterbilt 379 Trucks - Bullet Connector - Surface Mount - 31 LEDs - PBT-A31
Part Number
PBT-A31
Overview
This Triangle LED Turn Signal Light is DOT compliant and meets SAE requirements for use as a front turn signal light, clearance light, parking light, side marker light, and reflex reflector on 1987-2007 Peterbilt 379 trucks with triangle turn signals. The amber light fixture boasts 31 LEDs (21 on the front, 4 on the side, and 6 on the back) and consumes 90% less energy than incandescent lamps. This LED light features a foam anti-scratch pad and 1' power wires with bullet connectors for simple surface mounting and installation. A weatherproof, shatter-resistant polycarbonate lens is built to with stand impact with road debris and exposure to wet conditions. The LED truck light operates with in a 10-14.5 VDC range. Lifetime warranty on all truck/trailer lights. Price per fixture.
The Department of Transportation (DOT) sets strict guidelines in respect to external vehicle lighting that must be followed in order for a light to be street legal. Vehicle fixtures—such as headlights and taillights—that have a DOT compliance mark are legal, safe, and considered to provide suitable illumination for street use when properly installed.
An SAE mark means that the Society of Automotive Engineers has tested a product to ensure that it follows guidelines, standards, and practices in regard to design, construction, and materials. SAE's requirements do not guarantee that the product will be street legal. The product must be approved by the Department of Transportation (DOT) before it is considered legal for street use.
Super Bright LEDs, Inc. warrants that products carrying a lifetime warranty will be free from defects in the material and workmanship for the lifetime of the product. If Super Bright LEDs verifies that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product with the same product. In the case the exact product is no longer available, a gift card for the value of the original purchase price will be provided. Read More
Specifications
| Current Draw | 0.06A (60mA), 0.36A (360mA) |
|---|---|
| IP Rating | IP65 |
| Mount Type | Surface |
| Standards And Certifications | DOT Compliant, SAE Compliant |
| Voltage | 10-14.5 VDC |
| PC Rated | No |
.
Accessories & Power Supplies
Accessories Links
Accessory Category-
$0.45 ea.22-12 AWG Waterproof Silicone Filled Twist-On Wire Connector Part Number: WWN-2212In stockUL listed waterproof wire connectors suitable for all wire splices, especially those exposed to condensation, water, vapors or dust. 22-12 AWG Blue wire connector pre-filled with silicone to seal and protect connection from moisture. Not suitable for submersed connections. Price for each. -
$0.19 ea.Corrugated Split Loom Part Number: CSL-xIn stockCSL-x series black polyethylene corrugated split looms. Protects and conceal wires, cables, and tubings. Splits down the side to allow covering of pre-installed wiring. Corrugated split looms are available in 1/4", 3/8", 1/2", and 3/4" sizes. -
$9.95 ea.Weatherproof Dolphin Super B Connector with Sealant - 100 Pieces Part Number: DC-x-SIn stockDolphin Super B Connectors provide the industry’s most reliable connection with their unique design and tine structure. They reduce costs, will not corrode and do not require insulation stripping of most wire gauges before insertion. Weatherproof IP65 rating. Available in a 100 Pack.
-
$0.23 ea.16-14 AWG Butt Connectors - Butt Connectors Part Number: PSC-164In stockUse this butt connector to connect and seal 16-14 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun. -
$0.15 ea.Hole Snap-In Strain Relief Bushing Part Number: PSB-xIn stockEliminates sharp edges and protects wires and harnesses passing through holes in metal plates and panels. Resists up to 35 pounds pull. -
$0.39 ea.Black Cable Ties - 10 Pack Part Number: CT-B-10In stock4, 6, and 11 inch Cable tie - .875" max dia.; 6 inch Cable tie - 1.50" max dia.; 11 inch Cable tie with - 3.062" max dia.; 16 inch Stud Mount Cable tie - 4.125" max dia. -
$2.99 ea.3-Wire Pigtail for Trailer Lights - Female 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3FSIn stockDesigned to mate with a PL-3S Straight 3-Pin Plug or PL-3R Right Angle 3-Pin Plug, the 3-pin socket features 10 inch wires for easy installation. -
$1.99 ea.Dielectric Electrical Connector Grease - 4 Grams Part Number: CP-1In stockHigh performance silicone based dielectric grease that can be applied to any electrical connection to keep out moisture and prevent corrosion. Use with connectors, sockets, pigtails, trailer connections, headlight/taillight bulb bases, contacts, etc. Includes (1) 0.14-ounce packet. -
$0.99 per Foot4-Wire Trailer Wire - 16 Gauge Parallel Bonded Wire - Four Conductor - 16 AWG Power Wire Part Number: WP16-4In stockThis 4-wire trailer wiring is for low voltage installations. Parallel bonded four conductor 16 gauge 1x16 stranded wire. Commonly used for trailer wiring. Price per foot. -
$0.69 ea.Nylon Push Mount Base for Cable Ties - Push Mount Part Number: PMB-250In stockCable tie mounting base to secure wires on surface. Fits 1/4" diameter hole - For ties up to 3/8" wide. -
$1.99 ea.Heavy Duty Mount for Cable Ties Part Number: HDM-xIn stockHeavy-duty mount for cable ties to secure wires to surfaces up to 1/2" wide. A small tab inside the mounting hole temporarily engages threads, allowing assemblers to pre-install the mount on a stud before securing it with a washer and nut (not included). Available in #10 size mounting hole (1/4") and #8 size mounting hole (3/16"). Price for each.
-
$2.99 ea.3-Wire Pigtail for Trailer Lights - Female 3-Pin PL-3 Plug - 10" Lead Part Number: PL-3FSIn stockDesigned to mate with a PL-3S Straight 3-Pin Plug or PL-3R Right Angle 3-Pin Plug, the 3-pin socket features 10 inch wires for easy installation.
-
$0.45 ea.22-12 AWG Waterproof Silicone Filled Twist-On Wire Connector Part Number: WWN-2212In stockUL listed waterproof wire connectors suitable for all wire splices, especially those exposed to condensation, water, vapors or dust. 22-12 AWG Blue wire connector pre-filled with silicone to seal and protect connection from moisture. Not suitable for submersed connections. Price for each.
-
$0.19 ea.Corrugated Split Loom Part Number: CSL-xIn stockCSL-x series black polyethylene corrugated split looms. Protects and conceal wires, cables, and tubings. Splits down the side to allow covering of pre-installed wiring. Corrugated split looms are available in 1/4", 3/8", 1/2", and 3/4" sizes. -
$9.95 ea.Weatherproof Dolphin Super B Connector with Sealant - 100 Pieces Part Number: DC-x-SIn stockDolphin Super B Connectors provide the industry’s most reliable connection with their unique design and tine structure. They reduce costs, will not corrode and do not require insulation stripping of most wire gauges before insertion. Weatherproof IP65 rating. Available in a 100 Pack.
-
$0.23 ea.16-14 AWG Butt Connectors - Butt Connectors Part Number: PSC-164In stockUse this butt connector to connect and seal 16-14 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun.
-
$0.15 ea.Hole Snap-In Strain Relief Bushing Part Number: PSB-xIn stockEliminates sharp edges and protects wires and harnesses passing through holes in metal plates and panels. Resists up to 35 pounds pull. -
$0.39 ea.Black Cable Ties - 10 Pack Part Number: CT-B-10In stock4, 6, and 11 inch Cable tie - .875" max dia.; 6 inch Cable tie - 1.50" max dia.; 11 inch Cable tie with - 3.062" max dia.; 16 inch Stud Mount Cable tie - 4.125" max dia. -
$1.99 ea.Dielectric Electrical Connector Grease - 4 Grams Part Number: CP-1In stockHigh performance silicone based dielectric grease that can be applied to any electrical connection to keep out moisture and prevent corrosion. Use with connectors, sockets, pigtails, trailer connections, headlight/taillight bulb bases, contacts, etc. Includes (1) 0.14-ounce packet.
-
$0.99 per Foot4-Wire Trailer Wire - 16 Gauge Parallel Bonded Wire - Four Conductor - 16 AWG Power Wire Part Number: WP16-4In stockThis 4-wire trailer wiring is for low voltage installations. Parallel bonded four conductor 16 gauge 1x16 stranded wire. Commonly used for trailer wiring. Price per foot.
-
$0.69 ea.Nylon Push Mount Base for Cable Ties - Push Mount Part Number: PMB-250In stockCable tie mounting base to secure wires on surface. Fits 1/4" diameter hole - For ties up to 3/8" wide.
-
$1.99 ea.Heavy Duty Mount for Cable Ties Part Number: HDM-xIn stockHeavy-duty mount for cable ties to secure wires to surfaces up to 1/2" wide. A small tab inside the mounting hole temporarily engages threads, allowing assemblers to pre-install the mount on a stud before securing it with a washer and nut (not included). Available in #10 size mounting hole (1/4") and #8 size mounting hole (3/16"). Price for each.
Reviews
4.8 / 5 stars
15 reviews
4.8 / 5 stars
15 reviews
Write Your Own Review
Review Guidelines
superbrightleds.com reads and approves all reviews before listing them on the website. Below you will find a list of reasons that can result in your review being rejected.
- Review text does not pertain to the product
- Abusive and offensive language
- Photos are not related to the reviewed product
- Any violation of laws and/or copyrighted material
- Unrelated hyperlinks/URLs
Stay in touch & Save 10% on your next order!*