IT5 series Integrated LED Light Fixture comes in multiple lengths that can be linked together to reach desired length, up to 18ft. Designed as a general lighting solution for low-voltage applications, these compact fixtures can be surface mounted in RV or trailer interiors, food trucks, sheds, boat cabins, and more. The round frosted lens diffuses a wide beam of bright, glare-free light. Install one linear light bar on its own, or use included accessories to mount, connect, and power multiple fixtures together.
Product Details:
Accessories included: 2 mounting brackets, 2 mounting screws, 1 direct connector, 6in pigtail power adapter, 1 endcap
Extruded aluminum body, polycarbonate lens
Surface mount
Available in 4000K or 5000K
20 AWG pigtail connector
Operating Temperature: -13°–113° F (-25°–45° C)
120° beam angle
CRI 80+
Rated IP20 - suitable for damp locations
35000 hours (L70) lifetime
CE
Lifetime
In order for certain products within controlled categories, such as electrical and electronic devices, to be legally sold in the European Economic Area, they must bear a CE label, which stands for Conformité Européenne (European Conformity). Products with this label meet environmental, health, and safety standards put into place by European legislation.
Super Bright LEDs, Inc. warrants that products carrying a lifetime warranty will be free from defects in the material and workmanship for the lifetime of the product. If Super Bright LEDs verifies that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product with the same product. In the case the exact product is no longer available, a gift card for the value of the original purchase price will be provided. Read More
Applications
Trailer Interiors
Workbench
Utility Lighting
Sheds
RV Interiors
Food Trucks
Off Grid Lighting
Under-Cabinets
Boat Cabins
Specifications
Ambient Operating Temperature
-25~+45 °C (-13~+113 °F)
Brightness
400 lm/ft
Certifications/Compliance
CE
CRI
80+
Dimmable
No
Finish
Gray
IP Rating
IP20
LED Beam Angle
Beam angle is used to express the width of the light emitting from the source. The narrower the beam angle the more focused the light energy is. Comparing two 40 watt lights one with a beam angle of 30(a) and another with a beam angle of 90(b), They both produce the same amount of light output but (a) will appear brighter in the beam angle compared to (b) at the sacrifice of light spread.
Correlated Color Temperature is the hue, or tint of white to expect from a light source and is measured in kelvin.
Lower numbers give off a warmer white that is closer to candle light, and is good for relaxed and cozy spaces.
Higher numbers give off a cooler white light that will appear more blueish. While values to the middle of the spectrum give off a more neutral or natural white light that is similar to daylight.
Natural and cool white are considered ideal for task lighting.
Current Draw is used to size fuses and wire for an electrical circuit. Current draw is the amount of energy consumed by an LED or LEDs in an electrical circuit at a specific voltage, measured in amps (A) or milliamps (mA).
The Max Run of an LED strip is dependent on two things, voltage and density.
24 volt strips in most instances will give you a longer run than a 12 volt strip. However the LED density of the strip will have an effect on the maximum run.
If your install needs to extend beyond a strips Max Run additional power feeds can be run back to your power supply.
Shipping exclusions apply to some products, making them ineligible for free shipping. Any order with a combined weight of over 150 pounds or containing an excluded item will be excluded from free shipping automatically. One or more exclusions may apply to the same product as well. Exclusions per item may include, but are not limited to, the following:
• Any package with any two dimensions of the package over 30 inches. • Any package with a single side of the package over 42.3 inches. • Any package with a total combined length of the longest side added to 2 times the second and third longest sides over 130 inches. (L + 2H + 2W) • Any package with a weight over 50 pounds.
CPS-x2ST standard 5.5mm male or female barrel connector to screw terminal adapter. CPS-F2ST adapter allows products with pigtail power connections to be powered by CPS series power supplies.
CPS series Power Adaptor from DiodeDrive provides power for 24 VDC systems, with either 60 or 120-watts. The reliable Class II device has a fully enclosed plastic case and protection against short circuit and overload. 2-pin 120 VAC input. 5.5-mm barrel connector for easy powering.
CPS series Power Adaptor from DiodeDrive provides power for 12 VDC systems, in either 60 or 120-watts. The reliable Class II device has a fully enclosed plastic case and protection against short circuit and overload. 2-pin 120 VAC input. 5.5-mm barrel connector for easy powering.
Pigtail wire leads power adapter cable for compact power supplies. Allows products with power wires to connect with 5.5mm barrel connector. 63.5cm(25in) length.
CPS-EXTx extension cable for CPS power supplies or BPS-12VDC-x battery power supplies with 5.5mm barrel connector. Available in 100cm(39.3in) or 300cm(118in) length and is for low voltage DC cables.
Use these 3M 22-16 AWG grey wire connector for closed-end connections and secure splices. The UL-Listed twist-on wire connectors tighten with out ratcheting and feature a deep skirt to prevent bare wire from being exposed.
Power Adaptor from DiodeDrive provides power for 24 VDC systems. The Class II device has an enclosed plastic case and protection against electoral shock. 2-prong 120 VAC input. 5.5-mm barrel connector.
1 female 5.5mm barrel connector to 2 or 4 male 5.5mm barrel connectors for our CPS series power supplies. Easily power multiple products with one Compact Power Supply. 52.07cm(20.5in) length.
Power Adaptor from DiodeDrive provides power for 12 VDC systems. The Class II device has an enclosed plastic case and protection against electoral shock. 2-Prong 120 VAC input. 5.5-mm barrel connector.
Plug and Play in-line switch for CPS series power supplies and products. ON/OFF switch with 1 female and 1 or 2 male 5.5mm barrel connectors. 5 amps max at 12VDC. 31.75cm(12.5in) wire length.
Use this butt connector to connect and seal 22-18 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun.
CPS-x2ST standard 5.5mm male or female barrel connector to screw terminal adapter. CPS-F2ST adapter allows products with pigtail power connections to be powered by CPS series power supplies.
Pigtail wire leads power adapter cable for compact power supplies. Allows products with power wires to connect with 5.5mm barrel connector. 63.5cm(25in) length.
CPS-EXTx extension cable for CPS power supplies or BPS-12VDC-x battery power supplies with 5.5mm barrel connector. Available in 100cm(39.3in) or 300cm(118in) length and is for low voltage DC cables.
Use these 3M 22-16 AWG grey wire connector for closed-end connections and secure splices. The UL-Listed twist-on wire connectors tighten with out ratcheting and feature a deep skirt to prevent bare wire from being exposed.
1 female 5.5mm barrel connector to 2 or 4 male 5.5mm barrel connectors for our CPS series power supplies. Easily power multiple products with one Compact Power Supply. 52.07cm(20.5in) length.
Plug and Play in-line switch for CPS series power supplies and products. ON/OFF switch with 1 female and 1 or 2 male 5.5mm barrel connectors. 5 amps max at 12VDC. 31.75cm(12.5in) wire length.
Use this butt connector to connect and seal 22-18 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun.
Easily splice wires with out stripping insulation with single-channel or dual-channel "T" tap connectors. The non-weatherproof, insulated wire splice connectors are designed for 24-18 gauge wire and have a secure snap closure to hold wires in place. The clear design allows you to ensure that wires are connected. Use multiple combinations of single- and dual-channel connectors to reach your installation needs. Great for adding wires to an existing installation or starting a new one. Rated for 10 Amps at 300V AC/DC.
Use these pigtail power cords with your 12V or 120V T5 Linkable Linear LED Light Fixtures. Wire 12V T5 lights into a compatible power supply or 12V system, or wire 120V T5 lights into your home electrical system. The pigtail power cords can also be used to create custom interconnections.
Use this butt connector to connect and seal 16-14 AWG wire. The insulated vinyl terminal protects wire connections from water, salt, and corrosion. Seal with a heat gun.
Use this interconnect cable to join T5 Linkable Linear LED Task Lights. It's compatible with 12v and 120V integrated T5 lights and is available in 1' or 3.28' lengths.
CPS series Power Adaptor from DiodeDrive provides power for 12 VDC systems, in either 60 or 120-watts. The reliable Class II device has a fully enclosed plastic case and protection against short circuit and overload. 2-pin 120 VAC input. 5.5-mm barrel connector for easy powering.
Power Adaptor from DiodeDrive provides power for 12 VDC systems. The Class II device has an enclosed plastic case and protection against electoral shock. 2-Prong 120 VAC input. 5.5-mm barrel connector.
CPS series Power Adaptor from DiodeDrive provides power for 24 VDC systems, with either 60 or 120-watts. The reliable Class II device has a fully enclosed plastic case and protection against short circuit and overload. 2-pin 120 VAC input. 5.5-mm barrel connector for easy powering.
Power Adaptor from DiodeDrive provides power for 24 VDC systems. The Class II device has an enclosed plastic case and protection against electoral shock. 2-prong 120 VAC input. 5.5-mm barrel connector.
CPS series Power Adaptor from DiodeDrive provides power for 5 VDC systems, such as compatible LED strip lights. The reliable Class II device has a fully enclosed plastic case and protection against short circuit and overload. 2-pin 120 VAC input. 5.5-mm barrel connector for easy powering. Available in 3 wattage options.
Reviews
73%
3.7 / 5 stars
6 reviews
Write Your Own Review
Review Guidelines
superbrightleds.com reads and approves all reviews before listing them on the website. Below you will find a list of reasons that can result in your review being rejected.
Review text does not pertain to the product
Abusive and offensive language
Photos are not related to the reviewed product
Any violation of laws and/or copyrighted material
Unrelated hyperlinks/URLs
Choose sharing option
×
Email
URL
Save 10% on all orders by joining our mailing list