12 Volt LED Car Bulbs
LED Light Strips & Light Bars
LED Household Lighting
LED Landscape Lighting
Off Road LED Light Bars
LED Truck Lights
LED Work Lights
Emergency Vehicle & Strobe Lights
LED Accent Lighting
Motorcycle LED Lights
Boat, RV, and Other Lighting
LED Flashlights & Flashlight Bulbs
Industrial LED Lighting
Specialty LED Lighting
Hotel & Casino Lighting
Outdoor LED Light Strips - Waterproof LED Tape Light with 18 SMDs/ft., 1 Chip SMD LEDs 3528
- Select options to see various notes.
|50 - 99 pieces||$9.85 to $22.45 each|
|100 - 499 pieces||$8.76 to $19.96 each|
|500 - 999 pieces||$8.21 to $18.71 each|
|1000 + pieces||$7.67 to $17.47 each|
|For discount information or inquiring about larger quantity pricing, click here|
Add to Wishlist
Adding product to your Wishlist
There was a problem adding this product to your list. Make sure that you have chosen the necessary options (length, color, etc) and try again
If the problem persists, you can contact us directly
This product has been discontinued.
SE-WFLS series silicone encased waterproof flexible light strip with 30 or 60 high power 3528SMD LEDs. 12VDC operation. Half meter (19 inch long) or 1 meter (39 inch long) waterproof flexible light strips, can be cut into 3-LED segments. 3.5 inch connectors are on both ends for end-to-end connection. LEDs on highly flexible strip encased in flexible Waterproof Silicone. Silicone End Caps and Mounting Brackets available. Dimmable - See compatible LED dimmers.
Standards and Certifications
Waterproof LED Light Strips with Single Color LEDs
Outdoor LED Tape Light with 18 LEDs per Foot
1-Chip 3528 SMD LEDs
- Stair/Walkway LEDs
- Cove LED lighting
- Boat/Marine LED lights
- Display case LED lights
- Under cabinet lighting
|SE-WFLS-x60 series Flexible Light Strips use 3528SMD LEDs with 140° viewing angle|
|Beam Angle||140 degree|
|Water Resistance||Waterproof IP68|
|LED Lifetime||30000 Hours|
|LED Type||3528 SMD|
|LEDs per Segment||3|
|Lumen (Max)||264 Lumen|
|Standards And Certifications||CE/FCC/ISA Approved/ROHS Compliant/UL Listed|
|Strip Width||13mm (0.51in.)|
|Suitable for Vehicles||Yes|
|Type||Flexible Light Strips|
|Operating Voltage Range||9~14.8 VDC|
All specifications are subject to change without notice.
2. Max Run (or maximum run) is used to recommend the total number of devices that can run in succession without experiencing dimming due to excessive voltage drop in a series circuit (end to end). When Max Run is reached, power wires for additional devices must be 'home run' directly back to the power source, starting a new run.
|Part NO||Number of LEDs in Unit||Total Length||Emitting Color||CCT / Wavelength |
CCT is used to express the color or shade of white light. The Correlated Color Temperature is the measure of the color appearance of the light emitted from a light source, measured in degrees kelvin (K). The CCT rating is a general 'warmth' or 'coolness' measure of its appearance. Wavelength is used to express a specific color of light other than whites. Wavelength is the portion of the visible spectrum that the human eye can detect, between 380 and 700 nanometers (nm). When trying to match an existing bulb color choose a replacement that most closely matches the CCT or wavelength of the original.
|Intensity Per Foot||Intensity||Radiant Power||Beam Angle |
Beam angle is used to express the width of the light emitting from the source. The narrower the beam angle the more focused the light energy is. Comparing two 40 watt lights one with a beam angle of 30(a) and another with a beam angle of 90(b), They both produce the same amount of light output but (a) will appear brighter in the beam angle compared to (b) at the sacrifice of light spread.
|Current Draw per Foot @ 12 Volts DC |
Current Draw Per Foot is used to size power supplies, normally converted to watts per foot. This is equated using total wattage divided by number of linear feet. Current draw per foot is the amount of current consumed by an LED or LEDs in an electrical circuit per linear foot at a specific voltage, measured in milliamps (mA) or watts (W).
|Current Draw @ 12 Volts DC |
Current Draw is used to size fuses and wire for a circuit. Current draw is the amount of energy consumed by an LED or LEDs in an electrical circuit at a specific voltage, measured in amps (A) or milliamps (mA).
|SE-WFLS-CW60||60||39.8in (3.31ft)||Cool White||6000 K||62 lm/ft||204 lm||-||-||78 mA|
|SE-WFLS-NW60||60||39.8in (3.31ft)||Natural White||4500 K||80 lm/ft||264 lm||-||-||78 mA|
|SE-WFLS-WW60||60||39.8in (3.31ft)||Warm White||3300 K||67 lm/ft||222 lm||-||-||78 mA|
|SE-WFLS-B60||60||39.8in (3.31ft)||Blue||470 nm||16296 mcd/ft||54000 mcd||-||-||78 mA|
|SE-WFLS-G60||60||39.8in (3.31ft)||Green||525 nm||21728 mcd/ft||72000 mcd||-||-||78 mA|
|SE-WFLS-R60||60||39.8in (3.31ft)||Red||626 nm||18107 mcd/ft||60000 mcd||-||-||94 mA|
|SE-WFLS-Y60||60||39.8in (3.31ft)||Yellow||590 nm||18107 mcd/ft||60000 mcd||-||-||94 mA|
|SE-WFLS-R30||30||19.9in (1.66ft)||Red||626 nm||18107 mcd/ft||60000 mcd||-||-||94 mA|
- Wire Connectors
- Power Wires
- Power Supplies
Use our Calculator
Use our calculator.
Use our Calculator
Use our calculator.
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
I installed a strip of these in bright white. I used them as "porch lights" on my LeSharo motor home. I glued them to the rain gutter with Gorilla glue, and wired them up to the interior courtesy lights. So now when you open the door, the porch light goes on and illuminates your entry. I cut the strip into two lengths, that was easy. One length goes above the entry door, and one length glued to the undercarriage to illuminate the ground under your feet. Very nice.