Overview
This LED controller with wireless RF remote is perfect for operating your single-color LED light strips. Choose from 8 dynamic light modes with adjustable speed and brightness levels, and control your light strip from up to 50-feet away in open air. Power-cycle mode retention allows your light strip to return to the mode that was selected before it was powered off. The waterproof remote has a maximum load capacity of 15 amps and is compatible with LED light strips that operate within a 5-24V DC range. Wire leads connect to your light strip. Pair up to 3 remotes with the controller. Includes remote battery.
Press ‘I’ key to turn on unit or press ‘O’ key to turn off. Retains last setting between power off and power on.
Increases(+) or decreases(-) the brightness level of the light. Initiates Brightness Level Mode if Dynamic Mode is currently active.
Activates the brightness level indicated on the button label. These individual brightness levels are also accessible through the Mode(+)/Mode(-) Bright buttons.
Dynamic modes feature a variety of brightness transitions and patterns, with 8 distinct modes. These buttons initiate Dynamic Mode and cycle through the modes in ascending or descending order.
Increases(+) or decreases(-) the speed of the currently active dynamic mode. Initiates Dynamic Mode if Brightness Level Mode is currently active.
Adjusts brightness in static light mode. Press Flashes blue when remote is operating to indicate that the remote is functioning properly.
The controller/power supply operates at 5-24VDC. The red wire is positive(+) and the black wire is negative(-) as indicated on the controller housing. Make sure the power voltage matches the LED strip requirement. Incorrect voltage may damage the LED strip.
The red cable should be connected to LED positive and black cable to negative.
A multi-color emitting LED located on the remote controller indicates current operating status or operating status changes as follows:
Up to 3 wireless remotes can be assigned to operate the LED controller. Additionally, each individual wireless remote can be assigned to an unlimited number of controllers. The following steps show how to assign a new remote to the LED Controller:
- Disconnect the power to the LED controller, wait 5 seconds, and reconnect.
- Within 5 seconds of reconnecting the LED Controller, press the “50%” and “10%” buttons simultaneously.
- The LED indicator on the LED controller will flash white 3 times indicating the new wireless remote has been successfully assigned. This may be done for a total of 3 wireless remotes.
Up to 3 wireless remotes can be assigned to operate the LED controller. The following steps show how to assign a new remote to the LED Controller:
- Disconnect the power to the LED controller, wait 5 seconds, and reconnect.
- Within 5 seconds of reconnecting the LED Controller, press the “On” and “Bright (+)” buttons simultaneously.
- The LED indicator on the LED controller will flash yellow 3 times indicating the LED controller will recognize any remote.
View All
View All
View All
Specifications
Single Color LED Controller User Manual
Accessories & Power Supplies
Reviews
Overall Rating
Total Reviews
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
-
NameAnonymous
-
Technical LevelAverage
-
Part NumberMCBRF-15A
-
Reviewed On07/20/17
-
NameGary
-
Technical LevelAdvanced
-
Part NumberMCBRF-15A
-
Reviewed On05/05/17
RV awning rope light
I bought this product to lower the brightness of our 5th wheel awning rope LED, We do a lot of forest camping and before I installed this controller when out on a dark night and I would turn on this light it was like I was in a grocery store. Now I can see the stars.
-
NameKeith
-
Technical LevelAverage
-
Part NumberMCBRF-15A
-
Reviewed On11/12/16
-
NameCTD
-
Technical LevelAverage
-
Part NumberMCBRF-15A
-
Reviewed On08/28/18
Great dimmer
Had already installed a non dimmable transformer into a strip light lightbox. This allowed us to retrofit a dimmer by placing this module between the transformer and the 3 led 16' single density strips. Once we dimmed this to 50% we could use the main switch for on/off and it would keep that 50% setting. Wish this didn't have the additional flashing modes and was just a dedicated dimmer but that's a small annoyance. Well made and easy to install.
-
NameBurnie
-
Technical LevelAdvanced
-
Part NumberMCBRF-15A
-
Reviewed On02/06/19
