
Overview
Universal Red/Green/Blue (RGB) LED WiFi Compatible Controller & Dimmer without remote. Use to control up to four separate "zones" of RGB LED strips that will be linked and controlled by one or several wireless remotes or smartphones with the Wi-Fi LED Controller Hub. Synchronization function allows a single remote to operate one or multiple controllers (User configurable). Maximum load is 6 amps per channel, 24 amps total. Must be paired with Wi-Fi LED Controller Hub (WIFI-CON -- Sold separately) for adjusting all controller functions using a Smartphone or tablet running Android or iOS using the free MiLight 3.0 app.



- 1 - 2.4Ghz Sync-able RF Touch Color/ Mult-Zone Remote
- 1 - 2.4Ghz Wi-Fi RGB(W) LED Light Strip Controller
Installation Instructions Manual(Controller)
Remote & Installation Instructions
A master On(-)/Off(O) control for all zone-linked RGB(W) light strips. Also activates the “Master” function, which allows the remote to control the RGB(W) light strips of all zones. If a zone is currently active, pressing the master On(-) button restores the "Master" function to the remote.
Directly selects color along a circular spectrum. To obtain white light only, keep the “Zone On” (|) button depressed until the light changes to a steady bright white.
Flashes once to indicate when a command has been selected.


Increases(right side) or decreases(left side) the brightness level. Changing the active mode resets the brightness level to full.
Modes feature different color combinations, light transitions, and patterns, with 9 distinct modes. This button initiates the Mode function and scrolls through the modes in ascending order.
Increases (S+)/decreases(S-) the tempo of the mode pattern currently active
Allows up to four “zones” (i.e. channels) of RGB(W) light strips to be separately linked and controlled by the remote. Pressing one of the Zone On(|) buttons activates that zone; commands will affect only lights in that zone. Once linked to a zone, lights remain linked until they are unlinked. Steadily depressing the Zone On(|) button restores the lights in that zone to white.
Mode | Description | |
1 | RBGW Fade In/Out | Red, green, blue and white fade in/out in a set cycle. |
2 | Color Flash | Red, green, blue, white, purple and yellow flash in. |
3 | Disco | Red, green, blue, white, purple and yellow cycle in rotation with flashing transitions. |
4 | Red Fade In and Flash | Red brightens to full brightness, then flashes 3 times. |
5 | Green Fade In and Flash | Green brightens to full brightness, then flashes 3 times. |
6 | Blue Fade In and Flash | Blue brightens to full brightness, then flashes 3 times. |
7 | Color Fade In/Out and Flash | Multiple colors fade in/out and then flash randomly. |
8 | 3 Color Change with Fade In/Out | Multiple colors cycle with 3 smooth color changes followed by fade in/out. |
9 | White Fade In/Out | White flashes continuously. |
- Install 2 AAA batteries (not included) in the wireless remote.
- Make sure power to the controller is disconnected.
- Using a small flathead screwdriver, loosen the five clamp screws on the underside of the controller.
- Matching light strip wires to the labeled slots on the end of the controller, insert wires and tighten clamp screws, as shown below.
- Turn power on and wait until RGB(W) light strip illuminates. If no illumination occurs, check light strips and wiring connections.
- The RGB(W) light strip is ready for linking to the wireless remote.
- DO NOT use with wall dimmers, relays or other control circuits.
- DO NOT install with power applied to controller.
- DO NOT expose the remote or controller to direct or indirect moisture.
1. Switch off the main power supply to the light.
2. Restore power and within 3 seconds, choosing one of the "Zone On" (|) buttons, depress the button until the light begins flashing. It will flash white 2 times, indicating that the light is now linked to that numbered zone and can be controlled via the remote.

- Determine which zone the light is linked to. This can be done by testing the Zone On/Off controls for each zone on the remote.
- Switch off the main power supply to the light.
- Restore power and within 3 seconds, depress one of the "Zone On" (|) buttons until the light flashes 10 times, indicating that the light has been unlinked.
Specifications
Accessories & Power Supplies

Reviews
Overall Rating
Total Reviews
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.