Flush Mount LED Light Pod - 3" Square Work Light - 18W - 1,440 Lumens
Product Details
- Abrasion & scratch resistant lens
- Durable die cast aluminum housing
- IP67 water and dust proof
- Shock resistant
- Includes dampening flange
- Lifetime warranty
Overview
This flush-mount LED light pod is great for off-road driving lights, daytime running lights, or fog lights on your truck, ATV, or UTV and can also be used for industrial lighting, marine lighting, and tractor lighting. The 3" square mini auxiliary work light has 6 powerful LEDs that produce 1,400 raw lumens of cool white light. LEDs emit a 90° beam pattern. The durable LED work light is waterproof and shock resistant. A black-painted aluminum housing and polycarbonate lens protect internal components, and an integral heat sink allows LEDs to run cool, which leads to an incredibly long life span. The 18-watt LED light mounts flush and operates within a wide 9-32V DC range. Includes dampening flange, 20” wire lead with DT connector, and mating 12” DT pigtail adapter. Lifetime warranty on all LED work lights.
- LED Motorcycle Driving Lights
- Vehicle Auxiliary Lamps
- Motorcycle Daytime Running Lamps
- DRL Replacement Light
- Fog Light Replacement
- ATV Auxiliary Lights
- UTV Auxiliary Lights
- Agricultural Machinery Lighting
- LED Driving Lights
- Marine LED Lighting
View All
View All
View All
Specifications
| Part NO | Type | Power Consumption | Price | Operating Temperature | Lumen Per Dollar |
|---|---|---|---|---|---|
| AUX-18W-FMS90B | Fixture | - | $39.95 | - | 36.05 lumen/dollar |
| AUX-18W-FMS90B-2PK | Fixture | - | $79.90 | - | 36.05 lumen/dollar |
Accessories
Reviews
Overall Rating
Total Reviews
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
Rear Bumper Lights
These lights are amazing for mounting in a rear bumper as back up lights. I can see all the way down both sides of my 35' 5th wheel so no more dropping tires off the road. I will say if you dont have a bumper with the cut outs for lights. Cutting a factory rear bumper is a pain but the best tool is to drill a hole then use a sawsall. The grinder is a huge pain.
Excellent value for the money!
Pros:
Excellent Lighting.
Powder coated, not painted.
Comes with DT connectors (both female AND male ends!)
Comes with a rubber gasket.
Cons:
Does not include mounting bolts.
Male DT pigtail difficult to strip.
I'm currently running two of these lights in an aftermarket rear bumper on my Jeep Wrangler JK. They came excellently packaged in a generic box. They're solidly built and look to take many years of use and abuse. I was extremely pleased to see they came prewired with female DT connectors along with a male DT pigtail which made wiring a snap. My only real complaint is that no mounting hardware came included with the lights which required a trip to the hardware store. Other than that these are defiantly worth every penny and I'll be getting a couple of their pods to mount on my A pillar and front bumper!
Lastly, their customer service has been excellent. I have the good fortune to work near their office and everyone I've worked with has been amazing. Highly recommended.
Jeep back-up lights
I recessed two of these into a Rubicon Hard Rock bumper for off road maneuvering at night. Very bright, very tough, easy to wire in. On toughness- I replaced my exhaust with a high clearance system, and cut off the turndown to stop a rattle between it and the bumper. Unfortunately, this resulted in the exhaust super-heating the rear bumper. The light on the driver side had the reflectors partially melt (I melted the bottom of the license plate holder) on a 6 hr drive. The light continued to work and showed minimal distortion (a little digging on the lens). Otherwise, it held up. I replaced that light b/c @ $50, why not??? Great product!
