12 Volt LED Car Bulbs
LED Light Strips & Light Bars
LED Household Lighting
LED Landscape Lighting
Off Road LED Light Bars
LED Truck Lights
LED Work Lights
Emergency Vehicle & Strobe Lights
LED Accent Lighting
Motorcycle LED Lights
Boat, RV, and Other Lighting
LED Flashlights & Flashlight Bulbs
Industrial LED Lighting
Specialty LED Lighting
Hotel & Casino Lighting
18HP-LED Tower G4 Lamp
- This bulb is oversize, please see dimensions below.
|50 - 99 pieces||$13.46 each|
|100 - 499 pieces||$11.96 each|
|500 - 999 pieces||$11.21 each|
|1000 + pieces||$10.47 each|
|For discount information or inquiring about larger quantity pricing, click here|
This product has been discontinued.
Tower type G4 base Lamp with 18 High Power 3528 SMD LEDs. 12Volt AC or DC, 360 Viewing Angle, up to 155 lumen.
Standards and Certifications
|Beam Angle||360 degree|
|Comparable Wattage||20~25 Watts|
|Cross Reference Number||G4|
|LED Quantity||18 LEDs|
|LED Lifetime||50000 Hours|
|LED Type||3528 SMD|
|Lumen (Max)||155 Lumen|
|Operating Temperature||-30~+80 °C|
|Standards And Certifications||CE/FCC/ROHS Compliant|
|Storage Temperature||-40~+90 °C|
|Total Power Consumption||2.4 Watts|
|Operating Voltage Range||12V AC/DC|
Dimensions: 3.67cm(1.44") x 2cm(0.79") x 2cm(0.79")
All specifications are subject to change without notice.
1. Total product power consumption, measured in watts, including drive circuitry and controllers that make up the entire lamp.
|Part NO||Emitting Color||LED Wattage |
LED manufacturer's wattage rating
|Intensity per LED||Intensity||Beam Angle |
Beam angle is used to express the width of the light emitting from the source. The narrower the beam angle the more focused the light energy is. Comparing two 40 watt lights one with a beam angle of 30(a) and another with a beam angle of 90(b), They both produce the same amount of light output but (a) will appear brighter in the beam angle compared to (b) at the sacrifice of light spread.
Royal Blue is binned by radiometric power and peak wavelength rather than photometric lumens and dominate wavelength
|CCT / Wavelength |
CCT is used to express the color or shade of white light. The Correlated Color Temperature is the measure of the color appearance of the light emitted from a light source, measured in degrees kelvin (K). The CCT rating is a general 'warmth' or 'coolness' measure of its appearance. Wavelength is used to express a specific color of light other than whites. Wavelength is the portion of the visible spectrum that the human eye can detect, between 380 and 700 nanometers (nm). When trying to match an existing bulb color choose a replacement that most closely matches the CCT or wavelength of the original.
|Current Draw @ Operating Voltage |
Current Draw is used to size fuses and wire for a circuit. Current draw is the amount of energy consumed by an LED or LEDs in an electrical circuit at a specific voltage, measured in amps (A) or milliamps (mA).
|G4-CWHP18-TAC||Cool White||-||8.6 lm/led||155 lm||-||-||8500 K||195 mA||-||(Discontinued)|
|G4-WWHP18-TAC||Warm White||-||7.5 lm/led||135 lm||-||-||3300 K||200 mA||-||(Discontinued)|
|G4-BHP18-TAC||Blue||-||800 mcd/led||14400 mcd||-||-||466 nm||205 mA||-||(Discontinued)|
|G4-RHP18-TAC||Red||-||1000 mcd/led||18000 mcd||-||-||626 nm||145 mA||-||(Discontinued)|
Dimensions in millimeters (inches)
Use our Calculator
Use our calculator.
Use our Calculator
Use our calculator.
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
OK, but some strobing
I installed 2 of these in an over sink pendants on a Alum. bendable track with 1 MR16 and 2 pendant fixtures, much cooler no doubt, light output was adequate,,,but ocasionally they strobe, probably due to these fixtures on the same 12 volt power supply along with the MR16 LED (tried 4 different LED MR16, no good effect). Going to try the higher lumen 45 LED similar unit for about $5.00 more per unit (fingers crossed).
Your track power supply may have a minimum load requirement which is not being met when these LED bulbs installed, a higher power bulb may solve this problem.