LED Light Load Resistor Kit - LED Turn Signal Hyper Flash & Warning Fix

Part Number: RL-650-K
2 photos
Discontinued
In Stock
$4.95 ea.
Volume price as low as $3.71
Orders Ship Today!  5 Hours and 13 Minutes remaining
Notes
  • Select options to see various notes.

Overview

6 Ohm, 50 Watt load resistor kit. Solves common LED turn signal problems with hyperflashing and bulb out warning indicators. Connect one across each LED turn signal bulb to simulate filament Tail/Turn signal bulbs. Use the Flasher Selection Guide to determine the correct Flasher Relay for your vehicle.

View Installation Diagram & Instructions [PDF]. Mount the resistor away from painted surfaces, plastic, or other components that may be damaged by the heat generated by the resistor.

Super Bright LEDs, Inc. offers a 2-year warranty to protect against manufacturer defects and malfunctions. If you experience failure of an LED or other component not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product within the warranty period. If the same product is no longer available, a product of equal value may be substituted. Read More

Specifications

Clicking Sound No
Current Draw 2250mA
Ohms 6 Ohm
Type Load Resistor
Wattage 50 Watts
   
Stock Numbers: Load Resistor
Package Weight: 1.3oz (0.04kg)
Package Dimensions: 3.58" (9cm) x 1.06" (3cm) x 1.06" (3cm)
LED Light Load Resistor Kit Installation Guides:
RL-650-K - LED Light Load Resistor Kit - LED Turn Signal Hyper Flash & Warning Fix

Reviews

Overall Rating

Total Reviews

75

Tell Us What You Think

Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.

Sign In Required to Write a Review
Click here to sign in to your account
  • Name
    Jim in Florida
  • Technical Level
    Advanced
  • Part Number
    RL-650-K
  • Reviewed On
    10/01/14

They work, but be aware—they get extremely hot!

Once current is applied through these babies, they heat up to where they could give you a painful burn. I didn't actually measure the temperature, but I suggest you choose the mounting location very, very carefully and make certain you can isolate wires, plastic, or any other "meltable" material from them. Wish the heat sinks were more effective.

LED Light Staff Response

Jim thanks for taking the time to submit a review.Since the resistors are drawing enough power to simulate a 20 watt bulb they get just as hot as the bulb would. You are correct about placement that is why we have the warning note on the installation instructions to keep them away from painted surfaces and plastics.

Was this review helpful?
554

  • Name
    William
  • Technical Level
    Advanced
  • Part Number
    RL-650-K
  • Reviewed On
    06/05/13

2000 Mustang GT

With a sequential tail light kit installed only one resistor is required for each tail lamp assembly, wired to the first bulb in the sequence. It was a nice surprise that the included vampire clamps had dielectric grease already. I used 2 #4 3/8" sheet metal screws and two rubber washers to install behind the tail light assembly.

Was this review helpful?
5510

  • Name
    William
  • Technical Level
    Average
  • Part Number
    RL-650-K
  • Reviewed On
    09/08/14

Great Solution

This product came with instructions and was very easy to install. It was also a nice surprise that the dielectric grease was already installed in the connectors. My ’08 Tundra CrewMax was suffering from the “fast blink” after I installed led turn signal bulbs in the rear. After installing these resistor kits (one for each side), the blink rate returned to normal. The need for these is pretty simply. Led bulbs draw so much less current than typical incandescent bulbs that the vehicle’s electrical system thinks the bulb is burned out. The resistor adds resistance in the circuit which makes the system think it is seeing an incandescent bulb... Quick and easy solution. I would recommend this product!

Was this review helpful?
430

  • Name
    patrick
  • Technical Level
    Average
  • Part Number
    RL-650-K
  • Reviewed On
    11/15/14

Reliable

Have six of these hooked up to the six LED bulbs on my f150 for the past year and they have been working great so far without any flaws. Great product, price and company. Thanks.

Was this review helpful?
250

  • Name
    Kyle
  • Technical Level
    Average
  • Part Number
    RL-650-K
  • Reviewed On
    02/04/15

Don't forget some extra wire

You'll need to get some extra 20 gauge wire and connectors so you can mount these where they need to go, the wire pre-installed is too short.

Was this review helpful?
251


Send us your Feedback