Overview
Electronic LED Flasher Relays have no minimum load-12VDC. Eliminates the need for load resistors, turn signals will flash at normal rate with or without LED bulbs. Use the Flasher Selection Guide to determine the correct Flasher for your vehicle.
Specifications
Bulbs have Plus and Minus (like batteries) and will only work when polarity is correct. If bulb does not work when installed, turn it around in the socket.
Polarity Sensitive (NO)
Bulbs do not have Plus and Minus and will work either way installed in the socket.
| Material: | |||
| Case: Nylon pa6,6 + 15% Black | Base: Bakelite (black) | Fastons B, L: Cu Ni | |
| Technical Characteristics: | |||
| Nominal Voltage | Un | 12V | |
| Nominal Voltage | Un | 12V | |
| Operating Voltage | Uop | 11V...15V | |
| Pull-in Voltage | Ui | ≤11V@Tp | |
| Test Voltage | Up | 13V±0.2V | |
| Test Temperature | Tp | +20°C±2°C | |
| Switch Power | An | 0.02A - 15A | |
| Max. Power | Wm | Max. 150W | |
| Flashing Frequency | f | 90 TIMES/min±10% | |
| Operating Temperature | Top | -40°C...+80°C | |
| Storage Temperature | Tsto | +100°C/2h | |
| Life Time | -- | 200h/Wn CONTINUOUS/CONTINUOS |
|
| Operates Silently | -- | No | |
- These flashers do not replace all flasher units. Before you order, please see the pin outs of our flashers in the More Info page and compare with the one you are replacing. Click the part numbers for complete specifications. You can usually find your flasher pin out printed right on your flasher. Failure to check this and installation in an incompatible vehicle can blow your fuse, destroy the flasher and void the flasher warranty.
- Some of these flashers operate silently, they do not make the familiar clicking sound when operating. One solution is to connect a common automotive relay to the output along with your LED bulbs.
Reviews
Overall Rating
Total Reviews
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
-
NameJeff
-
Technical LevelAdvanced
-
Part NumberEP29L
-
Reviewed On04/15/13
Simple Solution
Product does exactly what it is intended to do perfectly.
Forget purchasing load resistors; get an LED flasher unit and you're done. Simple plug 'n play unit that gets your signals flashing at the correct interval.
My only gripe (a very minor one...) is that the 'click' noise is quite quiet compared to the OE unit, but that has no impact on the performance of the product. More of an fyi really...
Product was installed in a 2000 Chevrolet Blazer
-
NameNathan
-
Technical LevelAdvanced
-
Part NumberEP29L
-
Reviewed On06/16/15
blink fix
It fixed the blink rate of the blinkers and the hazards work.
but on my 01 yukon, when the headlights are off, and you toggle the directional switch, the parking lights alternate on and off with the blinker, if you have led's in the directional sockets. The fix is to either turn on the parking lights, whenever you go to use the blinker or use electrical tape over the photo cells on the dash to fool the headlights into thinking it is night time all the time and your lights will be on when the car is on.
-
NameWesley
-
Technical LevelAdvanced
-
Part NumberEP29L
-
Reviewed On01/16/16
-
NameMonty
-
Technical LevelAverage
-
Part NumberEP29L
-
Reviewed On05/04/15
-
Namekevin
-
Technical LevelAverage
-
Part NumberEP29L
-
Reviewed On08/02/16
works great in a buick
I had it installed in my 1999 buick century and it works great as intended.now I have the full effect of led lights.the flash interval when signaling.is the effect I was looking for.i have all lights led inside and out and front to back except the headlights.thats next.lol and I endorse this flasher 100 percent if you have a gm vehicle.
