
RF Touch Color Remote for MiLight/MiBoxer or Waterproof RGB/RGBW Controllers

Features
- Works with waterproof or MiLight/MiBoxer RGB or RGBW LED controllers
- Dynamic or static color modes
- Customized color, brightness, or speed settings
- Individual zone control
Overview
Use this wireless RF remote with Waterproof RGB or MiLight/MiBoxer RGB or RGBW controllers for LED strip light operation or with compatible LED smart bulbs and RGBW flood lights. Choose from thousands of color options with the touch-activated color-selection wheel, or select pure white. Control speed, brightness, and dynamic or static color modes from up to 98' away in open air. The remote also has 4 zone-control buttons for lights in different areas.
Please note: MiLight and MiBoxer are compatible smart technology brands. Products under these names are able to work interchangeably with each other.


- Remote Controlled Light
Specifications
- 1 - 2.4Ghz Sync-able RF Touch Color/ Mult-Zone Remote
- 1 - 2.4Ghz Wi-Fi RGB(W) LED Light Strip Controller (*required)
-
Installation Instructions Manual(Controller)
A master On(-)/Off(O) control for all zone-linked RGB(W) light strips. Also activates the “Master” function, which allows the remote to control the RGB(W) light strips of all zones. If a zone is currently active, pressing the master On(-) button restores the "Master" function to the remote.
Directly selects color along a circular spectrum. To obtain white light only, keep the “Zone On” (|) button depressed until the light changes to a steady bright white.
Flashes once to indicate when a command has been selected.


Increases(right side) or decreases(left side) the brightness level. Changing the active mode resets the brightness level to full.
Modes feature different color combinations, light transitions, and patterns, with 9 distinct modes. This button initiates the Mode function and scrolls through the modes in ascending order.
Increases (S+)/decreases(S-) the tempo of the mode pattern currently active
Allows up to four “zones” (i.e. channels) of RGB(W) light strips to be separately linked and controlled by the remote. Pressing one of the Zone On(|) buttons activates that zone; commands will affect only lights in that zone. Once linked to a zone, lights remain linked until they are unlinked. Steadily depressing the Zone On(|) button restores the lights in that zone to white.
Mode | Description | |
---|---|---|
1 | Six Color Fade In/Out | Red, Yellow, Green, Cyan, Blue and Purple fade in and out in a continuous repeating cycle. |
2 | White Fade In/Out | White fades in and out continuously. |
3 | RGBW Fade In/Out | Red, Green, Blue and White fade in and out in a continuous repeating cycle. |
4 | Seven Color Flash | Red, Green, Blue, Yellow, Purple, Cyan and White cycle in set pattern with flashing transitions. |
5 | Disco Random Pattern | Red, Green, Blue, Yellow, Purple, Cyan and White cycle at random with flashing transitions. |
6 | Red Fade In/Out with 3 Flashes | Red increases to full brightness then flashes 3 times. |
7 | Green Fade In/Out with 3 Flashes | Green increases to full brightness then flashes 3 times. |
8 | Blue Fade In/Out with 3 Flashes | Blue increases to full brightness then flashes 3 times. |
9 | All Pattern Mode | All 8 patterns above cycle through and repeat. |
- Install 2 AAA batteries (not included) in the wireless remote.
- Make sure power to the controller is disconnected.
- Using a small flathead screwdriver, loosen the five clamp screws on the underside of the controller.
- Matching light strip wires to the labeled slots on the end of the controller, insert wires and tighten clamp screws, as shown below.
- Turn power on and wait until RGB(W) light strip illuminates. If no illumination occurs, check light strips and wiring connections.
- The RGB(W) light strip is ready for linking to the wireless remote.
- DO NOT use with wall dimmers, relays or other control circuits.
- DO NOT install with power applied to controller.
- DO NOT expose the remote or controller to direct or indirect moisture.
1. Switch off the main power supply to the light.
2. Restore power and within 3 seconds, choosing one of the "Zone On" (|) buttons, depress the button until the light begins flashing. It will flash white 2 times, indicating that the light is now linked to that numbered zone and can be controlled via the remote.

- Determine which zone the light is linked to. This can be done by testing the Zone On/Off controls for each zone on the remote.
- Switch off the main power supply to the light.
- Restore power and within 3 seconds, depress one of the "Zone On" (|) buttons until the light flashes 10 times, indicating that the light has been unlinked.
Accessories

Reviews
Overall Rating
Total Reviews
Tell Us What You Think
Share your own experience and photos of this product. Doing so will help inform other potential buyers and allow us improve our product lines. It may take up to 72 hours for your review to appear.
Great product, instructions are wrong for remote!
Love it so far, however the instructions for the remote were wrong! To get my remote to pair with my LED strip, I had to do the following:
Turn Off LED Strip
Put Batteries in Remote
Turn On LED Strip
Tap On Button (|) THREE TIMES for Specified Zone
LED Strip is now paired successfully. The instructions say to HOLD DOWN the ON button, which is false. It took me forever to find instructions online that worked!
not the easiest controller to use and set up.
This controller is, if you read the set up instructions carefully, is tuff to set up when you have RGB strips that are not on the same power supply. Also the batteries wear out quickly. Would not be using this again unless all the strips are on the same PS. There also should be some indication what mode it is in out of the 9 that it can provide. A good place to start when operating is to press the mode button until you reach the DISCO function, now you would know where you are at.