5m Dim-to-Warm White LED Strip Light - Dynamic Color Tape Light - 3000K–1800K - 90+ CRI - 24V
Part Number:
STN-B-N30K90-C14A-12X5M-24V
Manufacturer Part Number:
$79.99
ea.
Was
Out of Stock
Backorder Available
Similar Products Available Today
Features
- Dim-to-warm 3000K-1800K up to 495 lm/ft
- 90+ CRI for quality color rendering
- Flexible, cuttable, 3M™ adhesive-backed design for easy install
- Lifetime Warranty
Ask About This Product
Get instant AI-powered answers
Try asking:
Most Popular Compatible Products
Overview
Use the 5m Dim-to-Warm White LED Strip Light to provide up to 8,120 lumens (495 lm/ft) for your kitchen, bedroom, or living room lighting project. Dim-to-warm LED strip lights mimic incandescent lights. They shift from 3000K at full brightness to ultra-warm white 1800K at half brightness, holding at 1800K down to full dim. A 90+ CRI gives accurate color rendering. Easily customize the strip using the cut segments every 3.94 inches. Flexible construction and 3M™ adhesive backing make installing it on curved surfaces and around edges easy.
Product Details:
- SMD 2835 LEDs
- IP20, suitable for dry locations
- Surface mount with 3M adhesive backing
- Up to 85 lm/W
- 24 VDC
- UL Listed
- Lifetime Warranty
STN-B-N30K90-C14A-12X5M-24V Specification Sheet Dimensional Drawings
Applications:
- Cabinets
- Under-Cabinet Lighting
Super Bright LEDs, Inc. warrants that products carrying a lifetime warranty will be free from defects in the material and workmanship for the lifetime of the product. If Super Bright LEDs verifies that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product with the same product. In the case the exact product is no longer available, a gift card for the value of the original purchase price will be provided. Super Bright LEDs administers all warranty claims in-house. Read More
Underwriters Laboratories (UL) LLC is an independent testing agency that works to verify product safety and quality. A UL-Listed label means that product samples have been tested by UL and that the product meets their Standards for Safety requirements.
Dim-to-warm
Dim-to-warm LEDs gradually shift to a warmer CCT (typically 1800K-2200) as they dim, mimicking the look of traditional incandescent lights.
Ask About This Product
Get instant AI-powered answers
Try asking:
Products Mentioned
Press Enter to send, Shift+Enter for new line
Responses are AI-generated from product documentation. For confirmation or more information, contact Super Bright LEDs customer service.
Conversations are recorded for quality assurance. More information
Ask About This Product
Get instant AI-powered answers
Try asking:
Products Mentioned
Press Enter to send, Shift+Enter for new line
Responses are AI-generated from product documentation. For confirmation or more information, contact Super Bright LEDs customer service.
Conversations are recorded for quality assurance. More information
Ask About This Product
Get instant AI-powered answers
Try asking:
Specifications
| Ambient Operating Temperature | -20 to 60 °C (-4 to 140 °F) |
|---|---|
| Certifications/Compliance | UL Listed |
|
Color Temperature
Color Temperature
 Correlated Color Temperature is the hue, or tint of white to expect from a light source and is measured in kelvin. Lower numbers give off a warmer white that is closer to candle light, and is good for relaxed and cozy spaces. Higher numbers give off a cooler white light that will appear more blueish. While values to the middle of the spectrum give off a more neutral or natural white light that is similar to daylight. |
Dim-to-Warm (1800K-3000K) |
| CRI | 90+ |
|
Current Draw
Current Draw
Current draw is calculated using the following formula: W/V = A, where W = the amount of power your light needs (wattage), V is the electrical system voltage (e.g., 120V AC), and A = amps. An ampere or amp (A) is the standard unit for electrical current. A milliamp (mA) equals one-thousandth of an amp, or 1000 mA is equivalent to 1 A.
Choosing LED fixtures with the correct amperage ensures safe and proper operation, preventing damage or injury. We recommend having all electrical components and fixtures installed by a certified professional electrician or lighting technician in compliance with all relevant standards and regulations. |
4 A |
|
Current Draw per Foot
Current Draw per Foot
Current Draw Per Foot is used to size power supplies, normally converted to watts per foot. This is equated using total wattage divided by number of linear feet. Current draw per foot is the amount of current consumed by an LED or LEDs in an electrical circuit per linear foot at a specific voltage, measured in milliamps (mA) or watts (W).
|
244 mA |
| Dimmable | Yes |
| Dimmer Type | PWM |
| Efficacy | 85 lm/W |
|
Environmental Rating
Environmental Rating
Suitable for Dry Locations This marking indicates that you can use the light or component in a location not normally subject to dampness. This may include locations exposed to temporary dampness, such as a building under construction, provided that ventilation is adequate to prevent moisture accumulation. Use these fixtures in living rooms, bedrooms, offices, hallways, and similar areas. The marking may be "SUITABLE FOR DAMP LOCATIONS" or "DRY LOCATIONS ONLY."Suitable for Damp Locations Fixtures marked “SUITABLE FOR DAMP LOCATIONS” or “SUITABLE FOR WET LOCATIONS” can be installed in damp locations. A damp location is an exterior or interior location regularly or occasionally subject to moisture condensation on or around electrical equipment. It includes partially protected places such as covered patios and porches. Damp locations include any regularly muggy or humid area, such as above a kitchen sink or stove, and appropriately vented bathrooms near the tub or shower.Suitable for Wet Locations Fixtures and components marked "SUITABLE FOR WET LOCATIONS" can be installed in wet or damp locations. A wet location is anywhere water or other liquids may drip, splash, or flow on or against electrical equipment. A light marked "SUITABLE FOR WET LOCATIONS" may have additional markings that tell where and at what height it can be safely mounted. Uncovered outdoor areas like decks, gazebos, walls, and typical landscape lighting sites all fall under the heading of wet locations. |
Non-weatherproof, Suitable for Dry Locations |
| Finish | White |
| Input Connection Type | Pigtail |
|
IP Rating
IP Rating
 |
IP20 |
|
LED Beam Angle
LED Beam Angle
Beam angle is used to express the width of the light emitting from the source. The narrower the beam angle the more focused the light energy is. Comparing two 40 watt lights one with a beam angle of 30(a) and another with a beam angle of 90(b), They both produce the same amount of light output but (a) will appear brighter in the beam angle compared to (b) at the sacrifice of light spread.
|
120° |
| LED Color | Dim-to-Warm |
| LED Density | 42 LEDs/ft |
| LED Chip Type | 2835 SMD |
| LEDs per Segment | 14 |
| Length | 16.4 ft (5 m) |
| LED Lifetime | 50000 Hours |
| Lumens Per Foot | 498 lm/ft |
|
Max Run (Class 2)
Max Run (Class 2)
The Max Run of an LED strip is dependent on two things, voltage and density. 24 volt strips in most instances will give you a longer run than a 12 volt strip. However the LED density of the strip will have an effect on the maximum run. If your install needs to extend beyond a strips Max Run additional power feeds can be run back to your power supply.   |
16.4 ft (5 m) |
| Minimum Cut Length | 100mm (3.9in) |
| Operating Voltage | 24 VDC |
| Series | DynamicColor |
| Strip Width | 12mm (0.47in) |
| Wattage | 96 Watts |
| Wattage per Foot | 5.9 W/ft |
| Wire Length | 19 in. |
Accessories & Power Supplies
Reviews
Customer Submitted Photos
Write Your Own Review
Review Guidelines
Super Bright LEDs reads and approves all reviews before listing them on the website. Below you will find a list of reasons that can result in your review being rejected.
- Review text does not pertain to the product
- Photos are not related to the reviewed product
- Any violation of laws and/or copyrighted material
- Unrelated hyperlinks/URLs
Recently Viewed
Get a Quote for
Get 10%
off your order
And be the first to know about the new products, sales, and more.
By providing your phone number, you agree to receive marketing text messages about new
products,
sales, and more.
Consent is not a condition to purchase. Msg and data rates my apply.
Reply HELP for help and STOP to cancel. View our Terms
of
Service and Privacy Policy.
There was an error while subscribing your email address
Please try again later
This email address is already subscribed to our mailing list
Thank you for being a subscriber!
Thank you for signing up!
An email has been sent to
This email address previously signed up to receive emails.
Only first-time subscribers are eligible for % off their next order.
Loading...
Item Added
Part Number:
No accessories available for this product.
Loading...