Name: 36V White LED Strip Light - High CRI - HighLight Series Tape Light - IP20 - 5m / 30m
Brand: Super Bright LEDs
SKU: STN-A30K90-C10A-10B5M-36V
Price: 44.99 USD
Availability: InStock

Overview

Higher voltage LED Strip Lights can illuminate a longer distance with out the worry of voltage drop. As a part of the Highlight series, this tape light uses pro-grade 2835 LED chips to create a powerful yet efficient line of light. High CRI of 90+ renders truer, vivid colors. The low-profile and flexible construction is a versatile solution for a wide range of indoor spaces. Use as accent lighting in coves and architectural features, or as task light for under-cabinets, work benches, and more.

Product Details:

Strip Width: 10mm
0-100% dimmable
IP20 rated for indoor applications
36 VDC
Cuttable segment length: 6.56 in. (166.7 mm)
Density: 18 LEDs/ft

Underwriters Laboratories (UL) LLC is an independent testing agency that works to verify product safety and quality. A UL-Listed label means that product samples have been tested by UL and that the product meets their Standards for Safety requirements.

In order for certain products within controlled categories, such as electrical and electronic devices, to be legally sold in the European Economic Area, they must bear a CE label, which stands for Conformité Européenne (European Conformity). Products with this label meet environmental, health, and safety standards put into place by European legislation.

Super Bright LEDs, Inc. warrants that products carrying a lifetime warranty will be free from defects in the material and workmanship for the lifetime of the product. If Super Bright LEDs verifies that the defect was not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product with the same product. In the case the exact product is no longer available, a gift card for the value of the original purchase price will be provided. Read More

LED Strip Lights FAQs

What is the difference between 12V and 24V strip lights?

Most LED strips are extremely similar despite differences in voltage. They look the same and are capable of similar light output. Despite this, there are some key differences between voltages which affect use for various applications. 12-volt DC strips can be connected directly to a vehicle's 12-volt DC electrical system. Higher voltage strips (e.g. 24 VDC, 36 VDC, or 48 VDC) on the other hand allow for longer runs and higher densities of LEDs over their 12-volt counterparts. 120 VAC strips offer incredibly long max runs and the ability to power from a standard wall outlet. For the maximum run of a strip see max run in the specification table. Read More »

How long of a run can I make my strip?

The max run of an LED strip is dependent on two primary things—voltage and density.

Higher voltage strips will generally give you a longer run than comparable lower voltage strips (e.g. 24 VDC would have a longer max run than 12 VDC with the same type of strip and density). Similarly, lower density strips have the potential for longer runs than high density strips.

So essentially, max run can be lengthened by choosing a higher voltage and/or lower density version of a strip, but a higher voltage could also provide a similar max run at an increased density where brightness or 'line of light' are more of a concern. If an install needs to extend beyond a strips max run, additional power feeds can also be run back to the power supply from other points in the run.

Please refer to the max run spec listed in the specification table of each product information page for specific information about each strip. Read More »

How bright is the strip? What are lumens and how many do I need?

Lumens are the measure of how bright an LED strip will be when in use. The higher the lumen rating, the brighter the strip will be. Higher lumen strips are usually better for under cabinet and task lighting. Lower lumen strips are typically used for accent lighting applications.

Read More About: Lumens vs CCT vs CRI »

What is color temperature? Which one is best?

Graphic showing light output color temperature range

Correlated Color Temperature is the hue, or tint of white to expect from a light source and is measured in kelvin. Lower numbers give off a warmer white that is closer to candle light, and is good for relaxed and cozy spaces. Higher numbers give off a cooler white light that will appear more blueish. While values to the middle of the spectrum give off a more neutral or natural white light that is similar to daylight. Natural and cool white are considered ideal for task lighting.

Read More About: Lumens vs CCT vs CRI »

What accessories do I need?

The only thing you need for certain to power a strip light is a power supply. We offer accessories used for installation, such as connectors and aluminum mounting channels. As well as others that add functionality such as such as dimmers, switches, and remote controls. Complete kits are also offered which include everything you need to get started.

36 Volt Power Supplies

Strip Connectors

Controllers

Housings

Installation Supplies

LED Strip Light Power Supply Calculator

Calculate the minimum power supply capacity needed for your installation. Minimum wattage is calculated as estimated wattage / 0.80 to give you the 20% wattage overhead necessary to improve power supply longevity.

Outdoor?

Yes No

Length (in feet) Voltage Wattage (per foot)

Calculate

Minimum Power Supply Wattage:
xx watts.

Shop Indoor Power Supplies

We've pre-filtered compatible power supplies for you based on voltage and weatherproofing requirements. Double check your wattage selection based on the calculation above before adding to cart. Many of our power supplies are offered in multiple wattages.

Specifications

Ambient Operating Temperature	-20~+45 °C (-4~+113 °F)
Brightness	170 lm/ft (558 lm/m)
Certifications/Compliance	CE, UL Listed
CRI	90+
Current Draw per Foot Current Draw Per Foot is used to size power supplies, normally converted to watts per foot. This is equated using total wattage divided by number of linear feet. Current draw per foot is the amount of current consumed by an LED or LEDs in an electrical circuit per linear foot at a specific voltage, measured in milliamps (mA) or watts (W).	51mA
Dimmable	Yes
Efficacy	93 lm/W
Environmental Rating Learn more about environmental rating	Non-weatherproof, Suitable for Dry Locations
Finish	White
IP Rating	IP20
LED Beam Angle Beam angle is used to express the width of the light emitting from the source. The narrower the beam angle the more focused the light energy is. Comparing two 40 watt lights one with a beam angle of 30(a) and another with a beam angle of 90(b), They both produce the same amount of light output but (a) will appear brighter in the beam angle compared to (b) at the sacrifice of light spread.	120°
LED Density	18 LEDs/ft
LED Type	2835 SMD
LEDs per Segment	10
Max Run (Class 2) The Max Run of an LED strip is dependent on two things, voltage and density. 24 volt strips in most instances will give you a longer run than a 12 volt strip. However the LED density of the strip will have an effect on the maximum run. If your install needs to extend beyond a strips Max Run additional power feeds can be run back to your power supply.	Up to 49.2ft (15m)
Minimum Cut Length	166.7mm (6.56in)
Operating Voltage	36 VDC
Rated Life (L70)	50000 Hours
Series	HighLight
Strip Width	10mm (0.39in)
Wattage per Foot	1.8 W/ft (6 W/m)
Wire Length	19in (48.3cm)

Print Specifications

Part NO	CCT Value CCT Value	Color Temperature Color Temperature Correlated Color Temperature is the hue, or tint of white to expect from a light source and is measured in kelvin. Lower numbers give off a warmer white that is closer to candle light, and is good for relaxed and cozy spaces. Higher numbers give off a cooler white light that will appear more blueish. While values to the middle of the spectrum give off a more neutral or natural white light that is similar to daylight. Natural and cool white are considered ideal for task lighting.	Current Draw Current Draw Current Draw is used to size fuses and wire for an electrical circuit. Current draw is the amount of energy consumed by an LED or LEDs in an electrical circuit at a specific voltage, measured in amps (A) or milliamps (mA).	Length	Power Consumption
STN-A30K90-C10A-10B30M-36V	3000K	Warm 3000K	5A (5000mA)	98.4ft (30m)	180 Watts
STN-A30K90-C10A-10B5M-36V	3000K	Warm 3000K	0.83A (830mA)	16.4ft (5m)	30 Watts
STN-A40K90-C10A-10B30M-36V	4000K	Natural 4000K	5A (5000mA)	98.4ft (30m)	180 Watts
STN-A40K90-C10A-10B5M-36V	4000K	Natural 4000K	0.83A (830mA)	16.4ft (5m)	30 Watts
STN-A50K90-C10A-10B30M-36V	5000K	Cool 5000K	5A (5000mA)	98.4ft (30m)	180 Watts
STN-A50K90-C10A-10B5M-36V	5000K	Cool 5000K	0.83A (830mA)	16.4ft (5m)	30 Watts

Accessories & Power Supplies

All Accessories

Channels

Connectors

36V Power Supplies

Installation Supplies

Controllers

Accessories Links

Accessory Category

Accessory Type:

$19.99 ea.

Mean Well LED Switching Power Supply - LPV Series 35-100W Single Output LED Power Supply - 36V DC Part Number: LPV-x-36
In stock

The 36V DC LPV Series 35-100W single-output LED power supply from Mean Well is a reliable and economical 100-240 VAC power supply suitable for LED lighting and LED moving sign applications with short circuit, overload, and over-voltage protection.
$23.99 ea.

Mean Well LED Switching Power Supply - SE Series 450-600W Enclosed Power Supply - 36V DC Part Number: SE-x-36
In stock

A low cost, economical LED power supply. Provides protections against short circuit, over load, over voltage. Low cost, high reliability. Made by Mean Well.
Starting at $38.99 ea.

Mean Well LED Switching Power Supply - PWM Series 40-200W LED Power Supply - 36V Dimmable Part Number: PWM-x-36
In stock

A low cost, economical LED power supply. Provides protections against short circuit, over load, over voltage. Low cost, high reliability. Made by Mean Well.

$0.25 ea.

10mm Silicone End Cap - 10mm End Cap - No Holes Part Number: EC10
In stock

10mm silicone end cap for use with ST10 silicone tubing and WFLS-GL sealant. There are no hole inserts for ending runs.
$0.25 ea.

10mm Silicone End Cap - 2 Holes - 10mm End Cap - 2 Holes Part Number: EC10-2
In stock

10mm silicone end cap with 2 holes for wiring, to be used with silicone tubing and WFLS-GL waterproof sealant.
$1.49 ea.

ST10 10mm Silicone Tubing - 10mm Silicone Tubing - 0.5m Part Number: ST10
In stock

10mm silicone tubing for use with non-weatherproof strips that are less than 10mm in diameter to create a waterproof product. Use tubing in conjunction with silicone end caps and glue/sealant. Price per 1/2 meter (19.7in), multiple quantities will come as one continuous tube.
$1.99 ea.

10mm LED Strip Light Mounting Clips With Adhesive Backing - 10 Pack Part Number: SBL-NKL-10
In stock

Use to mount 10mm LED strip lights. The pack includes 10 clips with an adhesive backing.

Reviews

%

0 / 5 stars

0 reviews

Write Your Own Review

Write a Review

You're reviewing: 36V White LED Strip Light - High CRI - HighLight Series Tape Light - IP20 - 5m / 30m

Select Product

Select Rating

1 star 2 stars 3 stars 4 stars 5 stars

Nickname

Email Address

Summary

Review

Technical Level

Add your photo

Review Guidelines

superbrightleds.com reads and approves all reviews before listing them on the website. Below you will find a list of reasons that can result in your review being rejected.

Review text does not pertain to the product
Abusive and offensive language
Photos are not related to the reviewed product
Any violation of laws and/or copyrighted material
Unrelated hyperlinks/URLs

36V White LED Strip Light - High CRI - HighLight Series Tape Light - IP20 - 5m / 30m

Features

Product Photos

Dimensional Drawings

Videos

Overview

Specifications