Wireless Remote Control Switch with Key Fobs -1 Channel

Wireless Remote Control Switch with Key Fobs

Part Number
RCA-RFx

Discontinued

We have discontinued this product permanently. Please find suggested replacement products from below section.

Overview

Wireless Remote Control System for 12VDC LED products. Available in single or dual channel receiver with 2 brushed aluminum fobs and 2A fuse integrated in fuse holder. 1.5A total maximum load, 100ft (30m) remote signal range. Great for accent lighting applications.
2 Years
2 Years
Super Bright LEDs, Inc. offers a 2-year warranty to protect against manufacturer defects and malfunctions. If you experience failure of an LED or other component not caused by negligence, abuse, unauthorized repair or disassembly, we will replace the product within the warranty period. In the case the exact product is no longer available, a product of equal value may be substituted or a gift card for the value of the product. Read More

Specifications

Amps 1.5 Amps
Battery Type 1 x 27A
Input Connection Type Pigtail
Standards And Certifications RoHS Compliant
Print Specifications
Swipe left to see additional specifications
Part NO Amps Per Channel Channels
RCA-RF1 1.5 Amps/CH 1 Channel
RCA-RF2 0.75 Amps/CH 2 Channels
Parts Include:
1 - RF Controller Box
2 - Key Fob Remote
1 - Inline Fuse Holder
1 - 2A Fuse
Important Note
Please check your state and local laws before installing aftermarket lighting accessories on vehicles. Every state has different policies and procedures for aftermarket accessories. Super Bright LEDs, Inc. is not responsible for any fines that you may incur while using vehicle lighting accessories purchased from Super Bright LEDs, Inc
Pre-test & Configure
Connect LED light’s positive wire (+) to the positive blue wire labeled “LED +” from RF controller box, and light’s negative wire (-) to the negative green wire labeled “LED -” from RF controller box.
Temporarily connect red wire labeled as “BATT +” with fuse holder to positive contact on battery and black wire labeled as “BATT -” to negative contact on battery. Use remote fob to test for proper light, controller, and remote operation. Press button “D” to turn lights on and off.
Make sure wires can be routed in a such a way that they will not be pinched, cut, or exposed to direct heat or moving parts. If a power wire is pinched it could cause the controller and lights to malfunction, and may void the warranty due to physical damage.
Installation
1. Locate battery and unhook the battery negative (-) cable.
WARNING: Negative (-) battery cable must be unhooked first to avoid fire hazard Using the diagram as a guide, connect one channel’s negative wires (-) from LED lights to the the negative
2. Using the diagram as a guide, connect one channel’s negative wires (-) from LED lights to the the negative green wire labeled “LED -” from RF controller box. Connect same channel’s positive wires (+) from LED lights to the positive blue wire labeled “LED +” from RF controller box. (Diagram 1). ONLY APPLIES TO RCA-RF2: Repeat this step for the 2nd channel of wires for alternating set of LED lights
3. Route wires to RF controller box location and secure wires using zip ties or other wire organization methods.
4. Secure the RF controller box to a safe and dry location near battery using zip ties or double sided adhesive.
5. Secure the RF controller box to a safe and dry location near battery using zip ties or double sided adhesive.
6. Connect the remaining red power wire with integrated fuse from the RF controller box labeled as “BATT +” to positive (+) contact of battery. (Diagram 1). Alternate Method (Alt. Diagram 2)
a.) Alternately, the MFCT Mini Fuse Circuit Tap (not included) may be used. Connect the red power wire with integrated fuse from the RF controller box labeled as “BATT +” to the existing crimp connection on the MFCT.
b.) Locate vehicle fuseblock, remove any existing fuse and insert the MFCT tap.
c.) Install new mini fuse and reinstall original fuse in tap.
7. Reconnect battery negative (-) cable and test using the key fob remote for proper installation.
Safety
Observe polarity, reversing controllers polarity may damage unit
Power controller unit only from 12 VDC source
Never use with other than included 2 Amp / 12 Volt fuse, do not exceed 1.5 Amp maximum load. If you are blowing this fuse, it means you have a short somewhere in your wiring. Using a larger fuse could result in a fire or damaging your lights
Single Channel Wiring
Specifications
Dual Channel Wiring
Specifications
Single Channel Controller Functions
Specifications
Dual Channel Controller Functions
Specifications
Alt. Diagram
Specifications

Accessories & Power Supplies

  1. Black Cable Ties - 10 Pack - 11 Inch Long

    $0.49 per Pack

    Black Cable Ties - 10 Pack - 11 Inch Long Part Number: CT-B11-10
    In stock
  2. Black Cable Ties - 10 Pack - 4 Inch Long

    $0.39 per Pack

    Black Cable Ties - 10 Pack - 4 Inch Long Part Number: CT-B04-10
    In stock
  3. Black Cable Ties - 10 Pack - 6 Inch Long

    $0.45 per Pack

    Black Cable Ties - 10 Pack - 6 Inch Long Part Number: CT-B06-10
    In stock
  1. Black Cable Ties - 10 Pack - 11 Inch Long

    $0.49 per Pack

    Black Cable Ties - 10 Pack - 11 Inch Long Part Number: CT-B11-10
    In stock
  2. Black Cable Ties - 10 Pack - 4 Inch Long

    $0.39 per Pack

    Black Cable Ties - 10 Pack - 4 Inch Long Part Number: CT-B04-10
    In stock
  3. Black Cable Ties - 10 Pack - 6 Inch Long

    $0.45 per Pack

    Black Cable Ties - 10 Pack - 6 Inch Long Part Number: CT-B06-10
    In stock

Reviews

Write Your Own Review

Write a Review

You're reviewing: Wireless Remote Control Switch with Key Fobs

Review Guidelines

superbrightleds.com reads and approves all reviews before listing them on the website. Below you will find a list of reasons that can result in your review being rejected.

  • Review text does not pertain to the product
  • Abusive and offensive language
  • Photos are not related to the reviewed product
  • Any violation of laws and/or copyrighted material
  • Unrelated hyperlinks/URLs