Tail Brake/Turn Bulbs

24-LED 15mm Bayonet Based Bulbs

   
The unique design of our 24 LED bulbs feature 18 LEDs aiming out the end plus 6 radially mounted LEDs aiming out the sides.
This produces a more complete and even lens fill than conventional LED bulbs

30-LED 15mm Bayonet Based LED Bulbs


1156 and 1157 bulbs with 30 Super Bright narrow viewing angle LEDs
Note: these bulbs are oversized - please measure your bulbs housings and click "more info" below to see dimensional drawing to determine
if they will fit your application. Forcing them into sockets where they will not fit can break off the locking pins and void the warranty

   

30-LED Right Angle 15mm Bayonet Based Bulbs

30-LED Right Angle bulbs. The LEDs aim 90 degrees from the base for applications where standard LED bulbs are not effective, such as motorcycle brake/turn lamps. These bulbs are not suitable for overhead lighting in campers or other applications that require long on-times
1156 and 1157 - For applications where these bulbs will not fit, see our 1156-PCB-W24 in the "Other Bulb" category

3 Watt Luxeon LED 15mm Bayonet Based LED Bulbs



Our exclusive LX3 series bulbs use High Power 3 Watt Luxeon LEDs to
achieve light outputs even higher than standard filament bulbs
3 Watt LEDs feature super wide 130 degree beam angle to illuminate entire tail light lens

Current Draw and Lumen Output @ 12VDC:
1156-xLX3 - 185ma - 80 Lumens
1157-xLX3 - 76/270ma - 30/85 Lumens

5 Watt 15mm Bayonet Based LED Bulbs

These are by far the brightest LED Car Tail Light bulbs on the market
Our exclusive LX5 series bulbs use a 3 Watt Luxeon side emitting LED and 4 High Power surface mount LEDs
Achieves light outputs even higher than standard filament bulbs
220 degree beam angle illuminates entire tail light lens

Current Draw and Lumen Output @ 12VDC:
1156-xLX5 - 320ma - 132 Lumens
1157-xLX5 - 62/335ma - 20/134 Lumens

These bulbs were designed for and can only be used as vehicle brake/turn signal bulb replacements. To prevent over heating, they will automatically dim if turned on for long periods of time.

9-LED and 15-LED #67 / #68
15mm Bayonet Based Bulbs

 
9-LED and 15-LED #67 Bulb with 15mm single contact (1156 type) base
9-LED #68 Bulb with 15mm dual contact (1157 type) base
smaller diameter, shorter bulbs fit where standard 1156 and 1157 LED based bulbs will not fit

Wedge Based LED Car Bulbs

ELECTRONIC LED FLASHERS

We now offer 2-Pin and 3-Pin (1/4 inch spade lug type) LED compatible Flasher Units in this category
You should definitely use one of these instead of Load Resistors if we have one to fit your vehicle
They operate at the correct flash rate with LED or standard filament bulbs
10~15 Volts DC - Flash Rate: 80 per minute

Note that some of these flashers operate silently, they do not make the familiar clicking sound when operating. One solution is to connect a common automotive relay to the output along with your LED bulbs
Also note that these flashers do not replace all flasher units. Before you order, please see the pin outs of our flashers in the "more info" page below and compare with the one you are replacing. Click the part numbers for complete spec sheets. You can usually find your flasher pin out printed right on your flasher. Failure to check this and installation in an incompatible vehicle can blow your fuse, destroy the flasher and void the flasher warranty

One LOAD Resistor is required for each turn signal bulb

6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing or burnt out bulb indications. Resistor measures 1.96L x .64W x .60H inches, leads are 12 inches long.
Kit Includes gel filled moisture resistant splice taps.

CONNECTION INSTRUCTIONS: Using included splice taps, connect one wire to ground and the other wire to the turn/brake hot wire. Splice taps allow for installation without cutting your turn signal wires.

We also offer 25 Ohm, 25 Watt Load Resistor kits which can be used with LED side marker lights (194/168 type) to prevent bulb-out indicators from turning on.

Here you will find:
PCB series lamps - designed for RV and Boat overhead lighting applications
1142 bulbs - dual contact 15mm with no connection to metal base (single intensity)
24 and 6 Volt DC - 15mm bayonet base bulbs - Sailboat and Antique vehicle applications