Wireless Remote RGB Controller with Key Fobs

Part Number: RCA-RFRGB | UPC: 84778103560
Stock: In Stock
Items have been added to cart!
50 to 99 pieces$22.46 each100 to 499 pieces$19.96 each500 to 999 pieces$18.71 each1000 to + pieces$17.47 each
Order will ship Monday (04/21/2014)
Product Description
Wireless Remote RGB Controller for 12VDC RGB LED products. Includes 3 channel RGB receiver and 2 brushed aluminum key fobs and 2A fuse integrated in fuse holder. 1.5A total maximum load, 100ft (30m) remote signal range. Great for accent lighting applications.
Standards and Certifications
CEFCCROHS Compliant2 Warranty
Compatible Products

Wireless Remote Control Switch



Parts Include

1 - RF Controller Box
2 - Key Fob Remote
1 - Inline Fuse Holder
1 - 2A Fuse
Diagram

Alt. Diagram 2

Controller


Instructions

Important Note: Please check your state and local laws before installing aftermarket lighting accessories on
vehicles. Every state has different policies and procedures for aftermarket accessories. Super Bright LEDs, Inc. is not
responsible for any fines that you may incur while using vehicle lighting accessories purchased from Super Bright LEDs,
Inc.

Pre-test & Configure
Connect RGB LED light’s positive wire (V+) to the positive black wire from RF controller box, and RGB light’s Red,
Green, and Blue wires to the corresponding Red, Green, and Blue wires from RF controller box.

Temporarily connect red wire (+) with fuse holder to positive contact on battery and black wire (-) to negative contact on
battery. Use remote fob to test for proper light, controller, and remote operation. Press button “D” to turn lights on and
off.

Make sure wires can be routed in a such a way that they will not be pinched, cut, or exposed to direct heat or moving parts. If a power wire is pinched it could cause the controller and lights to malfunction, and may void the warranty due to physical damage.

Installation
  1. Locate battery and unhook the battery negative (-) cable.
    WARNING: Negative (-) battery cable must be unhooked first to avoid fire hazard
  2. Using the diagram as a guide, connect RGB LED light’s positive wire (V+) to the positive black wire from RF controller
    box, and RGB light’s Red, Green, and Blue wires to the corresponding Red, Green, and Blue wires from RF controller
    box. (Diagram 1)
  3. Route wires to RF controller box location and secure wires using zip ties or other wire organization methods.
  4. Secure the RF controller box to a safe and dry location near battery using zip ties or double sided adhesive.
  5. Connect single black wire to negative (-) contact of battery or any negative grounded metal part of vehicle. (Diagram 1)
  6. Connect the remaining red power wire with integrated fuse from the RF controller box labeled as “BATT +” to positive (+) contact of battery. (Diagram 1).
  7. Alternate Method (Alt. Diagram 2)
    a.) Alternately, the MFCT Mini Fuse Circuit Tap (not included) may be used. Connect the red power
    wire with integrated fuse from the RF controller box to the existing crimp connection on the MFCT.
    b.) Locate vehicle fuseblock, remove any existing fuse and insert the MFCT tap.
    c.) Install new mini fuse and reinstall original fuse in tap.

  8. Reconnect battery negative (-) cable and test using the key fob remote for proper installation.

Safety
  • Observe polarity, reversing controllers polarity may damage unit
  • Power controller unit only from 12V DC source
  • Never use with other than included 2 Amp/12 Volt fuse, do not exceed 1.5 Amp maximum load. If you are blowing this fuse, it means you have a short somewhere in your wiring. Using a larger fuse could result in a fire or damaging your lights
RGB Light Bars & StripsUniversal RGB Controllers and Dimmers
Numbers below represent the maximum number of units the controller can drive without the use of RGB amplifiers
RGB Amplifiers
Numbers below represent the maximum number of units the Amplifier can drive
ProductCurrent Draw @ 12 Volt DCProduct LengthMax Run*RCA-RFRGBRGB-A4RGB-WA4MRGB-A4MRGB-A4-CPSRGBW-A6
RGB-1-DI230ma0.305m (1ft)20652525252104
NFLS-RGB15-DI202ma0.5m (1.6ft)20759595959118
NFLS-RGB30-DI404ma1m (3.3ft)1032929292959
NFLS-RGB150-DI1855ma5m (16.4ft)20666612
NFLS-RGB150X23295ma5m (16.4ft)1033337
NFLS-RGB150-KIT1970ma5m (16.4ft)20666612
NFLS-RGB30X2-WHT808ma1m (3.3ft)511414141429
NFLS-RGBNW300X3-WHT4700ma5m (16.4ft)1022225
NFLS-RGBWW300X3-WHT3750ma5m (16.4ft)1033336
* Maximum number of light bars in one run (end to end) - for higher quantities, multiple runs back to the power supply, controller, or amplifier must be made to prevent excessive voltage drop Note: To determine the maximum number of any LED products on a single Power Supply - divide the total current capability of the power supply by the current draw of the LED product - then multiply that number by 0.8 (for 80% capacity)
Typically we do not respond to feedback e-mails. If you have a question/comment that is not a suggestion or feedback, please use our contact page.

We appreciate your feedback and in assisting us create the best shopping experience possible!
Name:
E-Mail Address:
Comment:

Adding product to your Wishlist

Image Loader

Uh-oh

There was a problem adding this product to your list. Make sure that you have chosen the necessary options (length, color, etc) and try again

If the problem persists, you can contact us directly

SUCCESS

This item was added to your wishlist.

View Your Wishlist or Continue Shopping