See All PhotosLDRF-RGB6-TC3 RGB Controller w/ RF Touch Color Remote
IMPORTANT NOTES. PLEASE READ BEFORE PURCHASING:- Do not use amplifier until max run of RGB Controller or RGB Amplifier is met.
| Product Description |
|---|
| Universal Red/Green/Blue (RGB) LED Controller & Dimmer with handheld RF Remote Color Wheel can control any 12~24VDC RGB LED products. Select from several static Single Color modes or 7 dynamic color-changing modes with speed, dimming, ON/OFF controls. Maximum load is 6 amps per channel, 18 amps total. |
| Standards and Certifications |
|---|
    |
| Compatible Products |
|---|
LDRF-RGB6-TC3: 12VDC RGB LED Controller |
||||||||||||||||||||||
Controller Connections Product Specifications
|
||||||||||||||||||||||
| Applications: | Direct access color selection and functions with dimmable and speed controls |
| Function: | Control 3 channel RGB LED products using wireless RF remote |
| Operating Voltage: | 12~24 VDC – match power supply voltage to RGB LED product voltage |
| Connection Mode: | Common Anode (+) |
| Output: | Three CMOS drain-open output |
| Maximum Load Current: | 12VDC – 6 Amps per channel (18 Amps total) 24VDC - 6 Amps per channel (18 Amps total) |
| Output Power: | 216W @ 12V / 432W @ 24V |
| Control Method: | Wireless RF Remote Control - Frequency 433MHz |
| Batteries Required: | Three AAA batteries |
| Modes: | 7 dynamic color changing / Warm White/ Cool White / Color Wheel |
| Operating Temperature: | -25~60°C |
Dynamic Modes
NOTES:
1.) Do not scratch the sensing area. Do not disassemble, repair, or modify the device.
2.) Disconnect the power (adapter) before installing/removing this controller.
3.) Do not use this device near water, or moisture for indoor use only.
4.) This product should only be operated from the type of power source indicated on the label.
Typical Wiring Schematic
RF Touch Color Remote Control
| RGB Light Bars & Strips | Universal RGB Controllers and Dimmers Numbers below represent the maximum number of units the controller can drive without the use of RGB amplifiers | RGB Amplifiers Numbers below represent the maximum number of units the Amplifier can drive | Product | Current Draw @ 12 Volt DC | Product Length | Max Run* | LDRF-RGB6-TC3 | RGB-A4 | RGB-WA4 | MRGB-A4 | MRGB-A4-CPS |
|---|---|---|---|---|---|---|---|---|
| NFLS-RGB150-KIT | 1970ma | 5m (16.4ft) | 2 | 9 | 6 | 6 | 6 | 6 |
| NFLSK-RGB150-RF | 1855ma | 5m (16.4ft) | 2 | 9 | 6 | 6 | 6 | 6 |
| NFLS-RGB15-DI | 202ma | 0.5m (1.6ft) | 20 | 89 | 59 | 59 | 59 | 59 |
| NFLS-RGB30-DI | 404ma | 1m (3.3ft) | 10 | 44 | 29 | 29 | 29 | 29 |
| NFLS-RGB150X2 | 3295ma | 5m (16.4ft) | 1 | 5 | 3 | 3 | 3 | 3 |
| * Maximum number of light bars in one run (end to end) - for higher quantities, multiple runs back to the power supply, controller, or amplifier must be made to prevent excessive voltage drop Note: To determine the maximum number of any LED products on a single Power Supply - divide the total current capability of the power supply by the current draw of the LED product - then multiply that number by 0.8 (for 80% capacity) | ||||||||
Verified Owner
