RGB LED Light Bars & Strips
| LED Light Bar Applications Include: | ||
|---|---|---|
|
|
|
Dream-Color Programmable Chasing RGB Strip
Dynamic color chasing, sequencing and changing RGB Strip with individually controllable LEDs. Silicone Encased Waterproof Flexible Light Strip 5 Meter (16.45ft)long with 160 High Power SMD RGB LEDs (80 ICs) - 5 VDC Operation - 1/2 meter 5 pin signal, positive, ground wire. Complete system consists of one RGB-DC83 Controller, SWDC-RGB160 Flexible Light Strip, and 5VDC Waterproof Power Supply.
WFLS and NFLS RGB series Flexible Light Strips
197 Inch Light Strip on reel with 150 High Power RGB LEDs, 39 Inch Light Strip with 30 High Power RGB LEDs, and 19.5 Inch Light Strip with 15 High Power RGB LEDs. 12 VDC Operation, Strips can be cut into 3-LED (4in.) segments. LEDs on highly flexible strip with adhesive backing. No RGB controller on board, strips have separate RGB power inputs and common anode wire, Use any of our Universal RGB Controllers below to dynamically control the strips - Due to voltage drop, after 10 meters run wire back to source.
RLBN-RGB30SMD RGB Narrow Rigid Light Bar
22.5 Inch long Non-weatherproof Narrow Profile Rigid Light Bar with 30 3-Chip RGB 5050SMD LEDs. 12 VDC Operation, Bars can be cut into 3-LED (2.20in.) segments. LEDs on Narrow PCB board with white finish. No RGB controller on board, bars have separate RGB power inputs and common anode female sockets, use mating RLBN-RGB30SMD Light bar interconnect and power jumpers. Use any of our Universal RGB Controllers below to dynamically control the bars - Due to voltage drop, after 10 meters run wire back to source.
Universal RGB Controllers & Amplifiers
Wireless or Wired versions of RGB Controllers that control our RGB-1 LED Bar (not RGB-2) and RGB Strips. RGB LED Bars and Strips can be set to different static colors or different adjustable flashing and fading patterns. 12VDC operation. Some controllers also have dimming capabilities.
NOT suitable for automobile applications
Both infrared and Radio frequency controllers, controllers with dimming capabilities, manually operated controller with knobs, controller with music trigger, and amplifiers for boosting signals to allow more bars/strips to be connected to a single controller.
RGB-CA12 Controller
Wireless RF Controller. Powers units on/off, 7 static color modes, 4 dynamic modes to cycle through colors with and without fade. Control speed of dynamic modes.
LDIR-RGB4 Controller
Wireless IR Controller. Controls are duplicated on unit. Powers units on/off, 7 static color modes, 4 dynamic modes to cycle through colors with and without fade. Control speed of dynamic modes. Brightness can be controlled on all non-fade modes.
LDK-RGB3 Dimmer (Manual Knob)
Knobs can be used to dim Red, Green, and Blue from 0 to 100 percent. Create almost endless RGB color combinations.
RGB-WA4 Amplifier
Waterproof RGB Amplifer is used to regenerate RGB signal for longer runs.
LDRF-RGB4 Controller
Wireless RF Controller. Powers units on/off, 8 Direct-Access static color buttons, 6 dynamic modes to cycle through colors by strobing or fading. Control speed of dynamic modes. Brightness can be controlled on all non-fade modes. Automatic mode to cycle dynamic modes randomly. Play/pause button.
LDRF-RGB4-A Controller (Music Trigger)
Wireless RF Controller. Built-in microphone with sensitivity knob or Line-Level audio input jack can be used to trigger color change. Powers units on/off, 7 static color modes, 4 dynamic modes to cycle through colors with and without fade. Control speed of dynamic modes. Brightness can be controlled on all non-fade modes.
RGB-1 series 36-LED Light Bars
12 inches long and have a total of 36 LEDs. Cycles through preprogrammed color patterns. User has no control over this. Micro Controller based controller/driver board slowly cycles through Red, Green, Blue, and many vivid transitional colors including: Aqua, Pink, White, Purple, Orange and Yellow.
Requires RGB Controller which includes power jumper and will drive up to 10 RGB Light Bars. Controller with one Light Bar draws a maximum of 220 ma (200 ma per additional Light Bar). 13VDC Maximum - NOT SUITABLE FOR AUTOMOBILE APPLICATIONS
RGB-2 series 36-LED Light Bars
12 inches long and have a total of 36 LEDs. User has full control of all functions with handheld IR remote control. Micro Controller based controller/driver uses IR receiver and handheld transmitter to select color pattern and cycle speed. Controller can also pause pattern (for selecting static LED color) and power system on/off, memory powers unit up in the same mode it was in when powered down. RGB-2 Controller will drive up to 200 RGB-2 Light Bars. 13VDC Maximum - NOT SUITABLE FOR AUTOMOBILE APPLICATIONS
12 Volt DC Power Supplies
Can be used for any of our 12 Volt LED products. See Power Supply selection guide
Compact, enclosed and waterproof 12VDC power supplies. Ranging from 5 Watts to 100 Watts, with 120~240VAC inputs.
12VDC CPS Power Supply
CPS series Compact Enclosed Power Supplies. 6, 12, 24, and 50 Watt 12VDC systems. 100~240VAC 50/60Hz Input. 4 foot long AC in and DC out cables
12VDC Waterproof Power Supply
Regulated Switching Power Supplies. 5 Watt, 10 Watt, 15 Watt, 30 Watt, 60 Watt, 100 Watt. 120VAC Input - 12VDC Output. Completely sealed with aluminum housing
12VDC Power Supply
Enclosed 12VDC Regulated Switching Power Supply. 100 Watt and 40 Watt. Input (VAC@Hz) 85-264@47-63.

Don't see what you're looking for here?
Please see our Accent Lighting category for automobile applications or our General Purpose category for utility lighting applications
|
![]() |







