superbrightleds.com
$0.00

LuxBar High Power LED Light Fixture
$ 12.95
  • LuxBar Linear Light with High Powered White 5050 SMD LEDs
  • 24VDC system - extensive selection of installation accessories
  • LuxBar System is extremely versatile and scalable
  • See all accessories and power supplies below
Enter Quantity:
LBFA-I LuxBar Interconnect Jumper
$ 0.25
  • LBFA Interconnect/Jumper for connecting LuxBar Linear Light Fixtures together
  • Available as Direct Connect, Right Angle, or Flat Type Jumpers from 25cm to 183cm
Enter Quantity:
LBFA-PS LuxBar 24VDC Power Supplies
$ 19.95
  • 24VDC Power Supplies for LuxBar series Light Fixtures seen above
  • 100~240VAC 50~60Hz input
  • See available Power Connectors below for connecting Fixtures to Power Supplies
Enter Quantity:
LBFA-P LuxBar Power Connectors
$ 1.95
  • 30cm, 50cm, and 100cm Power Connectors for connecting LuxBar series Light Fixtures to 24Watt or 48Watt LuxBar Power Supply
  • 50cm Pigtail Power Connector used for the 240Watt LuxBar Power Supply or other power source
Enter Quantity:
LBFA-SW LuxBar Power Switches
$ 3.95
  • LBFA series LuxBar Light Fixture On/Off Switch connects in between LuxBar Light Fixture and 24Watt or 48Watt LBFA-PS Power Supply
Enter Quantity:
LBFA-D LuxBar Dimmers
$ 49.95
  • LBFA series LuxBar Light Fixture Dimmer connects in between LuxBar Light Fixture and LuxBar Power Supply
  • 2 Channel Dimmer is used with either 24Watt or 48Watt LuxBar Power Supply
  • 4 Channel Dimmer is used with the 240Watt LuxBar Power Supply
  • Includes two 25cm interconnect Jumpers(LBFA-I25), two Direct Connect Jumpers(LBFA-I), and 6 screws
Enter Quantity:
LuxBar Interconnect Cable Joiners
$ 0.95
  • LBFA-JCC Cable to Cable Joiner to extend LBFA LuxBar Series Light Fixture Interconnects
  • LBFA-MCJ Multiple Cable to Cable extension joint with 1 input and 4 outputs
Enter Quantity:
LBFA-MC LuxBar Mounting Clips
$ 0.25
  • Mounting Clip with 1 included screw for LBFA LuxBar series Light Fixtures
  • Available in Flat Type or Angled (45 degree)
Enter Quantity:
CLL-xW7 LED Cabinet Light Fixture
$ 49.95
  • 7 Watt Cabinet Light Fixture with 6 High Powered White LEDs
  • 12 1/16 inches long, 24VDC system produces 325 lumens
  • Two mounting brackets with screws included
  • See 24VDC Power Supply and Interconnect Couplers below
Enter Quantity:
Cabinet Light Power Supply
$ 19.95
  • 24VDC Power Supply, 50Watt unit will power a maximum of 5 CLL-xW7 Light Fixtures seen above, 30Watt will power 3 Fixtures maximum
  • 6ft long AC in
  • 6.5ft DC out cables
  • 100~240VAC 50~60Hz input
Enter Quantity:
CLL-SW On/Off Switch Adapter
$ 9.95
  • CLL series LED Light Fixture On/Off Switch connects in between CLL Light Fixture and Power Supply
  • Includes one Mounting Bracket and one screw
Enter Quantity:
CLL-EXT24 Power Cable Extension
$ 9.95
  • Extension Cable for CLL Power Supplies seen above
  • adds 24 feet to low voltage DC cable
Enter Quantity:
CLL-I Interconnect Jumper
$ 3.95
  • CLL Jumper for connecting CLL-xW7 Cabinet Linear Lights together Available as Direct Connect, 12 inch length, or 36 inch length
Enter Quantity:
CLL-FF2 Female to Female Adapter
$ 1.95
  • Use for joining multiple CLL-I interconnect jumpers seen above to achieve longer lengths between fixtures
Enter Quantity:
CLL-PTFM36 Dimmer Wiring Kit
$ 9.95
  • Cables used for connecting our LDR-2A LED Dimmer in line with the CLL Power Supplies
Enter Quantity:
WLFA series Waterproof Light Fixture
$ 24.95
  • 1/2 meter and 1 meter Waterproof Light Fixtures sealed in aluminum housing
  • 12VDC operation with 8 inch female and male power wires on both ends with waterproof screw caps
  • 30 or 60 White High Flux Piranha LEDs with 90 degree beam pattern
  • Mount with Mounting Clips sold below
Enter Quantity:
WLFA-MC Mounting Clips
$ 0.29
  • Mounting Clip with screws for WLFA series Waterproof Light Fixture
  • One clip and 2 screws
Enter Quantity:
WLFA-PWS Power Wires
$ 5.95
  • Power Wire Set for WLFA series Light Bars with waterproof mating connectors
  • Wire is 6 inches long
  • Includes 1 wire with Male Connector and 1 wire with Female Connector
Enter Quantity:
LF series Light Fixture with Switch
$ 19.95
  • 19 3/4 inch Light Fixture with 30 High Power White SMD LEDs or 24 inch Light Fixture with 48 High Power White SMD LEDs in aluminum housing
  • 10~30VDC operation
  • Drivers and On/Off switch attached to 36 inch power wires
  • cannot cut switch off
  • Mounting Clips included
Enter Quantity:
WLF series Waterproof Light Fixture
$ 24.95
  • 12 or 24 inch Waterproof Light Fixture sealed in aluminum housing
  • 12VDC operation with 12 inch power wires on both ends
  • 30 or 60 Cool White or Warm White SMD LEDs with 120 degree beam pattern
  • Integrated Mounting Magnets included - WLF-CW60SMD can be purchased without magnets
  • Mount with Magnets, Foam Tape or Mounting Clips sold below
Enter Quantity:
WLF-MC Mounting Clips
$ 0.95
  • Set of Mounting Clips with included screws for WLF series Waterproof Light Fixture
  • One set is 2 clips and 2 screws
Enter Quantity:
RLB series Rigid Light Bar
$ 24.95
  • 15-3/4 Inch Rigid Light Bar with 6 High Power 0.5 Watt SMD 120 Degree LEDs
  • 12VDC Operation
  • 4 Pin flex needle sockets on ends
  • THIS IS OUR BRIGHTEST LIGHTBAR
  • See Jumpers and Power Supplies below
Enter Quantity:
RLB series Light Bar Connectors
$ 2.49
  • RLB Jumpers available in 6 or 36 inch lengths for connecting Rigid Light Bars together
  • CPS adapter for connecting to CPS power supply
  • 4 pin flex needle connectors
Enter Quantity:
RLB Rigid Light Bar Mounting Track
$ 0.45
  • Plastic Mounting Track for RLB series Rigid Light Bars
  • Two minimum required per Light Bar
  • Mount by adhesive backing or two screw holes spaced 1 1/8" apart
  • Tracks measure 1 1/2" wide x 7/8" long
Enter Quantity:
RLBN series Narrow Rigid Light Bar
$ 9.95
  • 19.5 Inch long Non-weatherproof Narrow Profile Rigid Light Bar with 30 1-Chip 3528SMD LEDs
  • 22.5 Inch long Non-weatherproof Narrow Profile Rigid Light Bar with 30 3-Chip 5050SMD LEDs
  • 12 VDC Operation
  • 1-Chip 3528SMD LED Rigid Light bar can be cut into 3-LED segments
  • 3-Chip 5050SMD LED Rigid Light bar can be cut into 1-LED segments
  • Use C21 Interconnect and Power Jumpers shown below
Enter Quantity:
RLBN-RGB30SMD Narrow Rigid Light Bar
$ 24.95
  • 22.5 Inch long Non-weatherproof Narrow Profile Rigid Light Bar with 30 3-Chip RGB 5050SMD LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • No RGB controller on board, strips have separate RGB power inputs and common anode wire
  • Use RLBN-RGB Interconnect and Power Jumpers shown below
Enter Quantity:
RLBN-RGB30SMD Light Bar Jumpers
$ 0.45
  • Interconnect Jumpers for connecting RLBN-RGB30SMD Narrow Rigid Light Bars together
  • Power Jumpers for connecting Light Bars to our Universal RGB Controllers
  • Available in 6 or 36 inch lengths
Enter Quantity:
SNFLS-x30 Flexible Light Strip
$ 12.95
  • 1/2 Meter (19.5 Inch) long Non-weatherproof Flexible Light Strip with 30 Side Emitting SMD LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • see optional FLB-MC mounting clips below
Enter Quantity:
SWFLS-x60 Flexible Light Strip
$ 26.95
  • Silicone Encased Waterproof Flexible Light Strip 1 Meter (39 Inch)long with 60 High Power Side Emitting SMD LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • 3.5 inch Connectors are on both ends for end-to-end connection
  • see SE-PC06 Power Connectors below if cutting strip
Enter Quantity:
SE-WFLS-x60 Flexible Light Strip
$ 23.95
  • Silicone Encased Waterproof Flexible Light Strip 1 Meter (39 Inch)long with 60 High Power SMD LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • 3.5 inch Connectors are on both ends for end-to-end connection
  • see Mounting Brackets and End Caps below
Enter Quantity:
SE-PC06 Power Connectors
$ 0.40
  • 4 inch male and female Power Connectors for connecting SE-WFLS series Waterproof Flexible Light Bars to 12 Volt power source
Enter Quantity:
SE-MB Mounting Clip
$ 0.10
  • Silicone Mounting clips for SE-WFLS series Silicone Encased Waterproof Flexible Light Strip seen above
  • Attach using 0.09 in. diameter screw holes
Enter Quantity:
SE-EC End Caps
$ 0.10
  • Silicone End Caps for SE-WFLS series Silicone Encased Waterproof Flexible Light Strip seen above
  • For use when cutting strip to enclose end
Enter Quantity:
NFLS-x30 Flexible Light Strip
$ 9.95
  • 1/2 Meter (19.5 Inch) long Non-weatherproof Flexible Light Strip with 30 High Power LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
Enter Quantity:
NFLS-x60 Flexible Light Strip
$ 19.95
  • 1 Meter (39 Inch) long Non-weatherproof Flexible Light Strip with 60 High Power LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
Enter Quantity:
NFLS-x300 Flexible Light Strip Reel
$ 99.95
  • 5 Meter (197 Inch) Non-Weatherproof Flexible Light Strip with 300 High Power LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • Sold on reel
Enter Quantity:
NFLS-x300X3 Flexible Light Strip Reel
$ 129.95
  • 5 Meter (197 Inch) Non-Weatherproof Flexible Light Strip with 300 High Power 3-Chip 5050SMD LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • Sold on reel
Enter Quantity:
WFLS-x30 Flexible Light Strip
$ 11.95
  • 1/2 Meter (19.5 Inch)long Weatherproof Flexible Light Strip with 30 High Power LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • PCB also available in Black color below
Enter Quantity:
WFLS-x30-BK Flexible Light Strip - Black Circuit
$ 11.95
  • 1/2 Meter (19.5 Inch)long Weatherproof Flexible Light Strip with 30 High Power LEDs
  • Black Color Circuit Strip
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
Enter Quantity:
WFLS-x60 Flexible Light Strip
$ 23.95
  • 1 Meter (39 Inch) long Weatherproof Flexible Light Strip with 60 High Power LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • PCB also available in Black color below
Enter Quantity:
WFLS-x60-BK Flexible Light Strip - Black Circuit
$ 23.95
  • 1 Meter (39 Inch) long Weatherproof Flexible Light Strip with 60 High Power LEDs
  • Black Color Circuit Strip
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
Enter Quantity:
WFLS-x300 Flexible Light Strip Reel
$ 119.95
  • 5 Meter (197 Inch) Weatherproof Flexible Light Strip with 300 High Power LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • Sold on reel
Enter Quantity:
xFLS-RGB15 Flexible Light Strip
$ 14.95
  • 19.5 Inch Light Strip with 15 High Power RGB LEDs
  • 12 VDC Operation
  • Bars can be cut into 3-LED segments
  • Highly flexible strip with adhesive backing
  • No RGB controller on board, strips have separate RGB power inputs and common anode wire
  • Due to voltage drop, after 10 meters run wire back to source
  • Available Weatherproof or Non-weatherproof
Enter Quantity:
xFLS-RGB30 Flexible Light Strip
$ 25.95
  • 39 Inch Light Strip with 30 High Power RGB LEDs
  • 12 VDC Operation
  • Bars can be cut into 3-LED segments
  • Highly flexible strip with adhesive backing
  • No RGB controller on board, strips have separate RGB power inputs and common anode wire
  • Due to voltage drop, after 10 meters run wire back to source
  • Available Weatherproof or Non-weatherproof
Enter Quantity:
xFLS-RGB150 Flexible Light Strip
$ 129.95
  • 197 Inch Flexible Light Strip with 150 High Power RGB LEDs
  • 12 VDC Operation
  • Can be cut into 3-LED segments
  • LEDs on highly flexible strip with adhesive backing
  • Due to voltage drop, after 10 meters run wire back to source
  • Available Weatherproof or Non-Weatherproof
  • Sold on reel
Enter Quantity:
RGB-4Wire
$ 0.40
  • Four Conductor RGB Light Strip 22 gauge wire
  • Use for connecting segments of RGB Light Strips
  • Price per foot
Enter Quantity:
Flexible Light Strip Interconnect Jumpers
$ 1.49
  • Solderless connectors, use for connecting NFLS series Flexible Light Strips and Strip segements
  • NOT for WFLS series Weatherproof Flexible Light Strips or NFLS-x300X3 series Flexible Light Strips
Enter Quantity:
WFLS Heat Shrink Tubing DWS-500
$ 0.89
  • 1/2" Dual Wall Heat Shrink Tubing
  • Use for Weatherproof sealing WFLS Flexible Light Strip interconnections
  • Sealant flows and encapsulates connections as tubing shrinks
  • price is per 6 inch piece
Enter Quantity:
LDRF-RGB4 RGB Controller w/ RF Remote
$ 44.95
  • Universal Red/Green/Blue (RGB) LED Controller & Dimmer with handheld RF Remote can control any 12VDC RGB LED products except the RGB-2
  • 8 individually selectable Dimmable Static Color Modes
  • Buttons on controller for direct access to all modes and functions
  • 6 individually selectable Dynamic Color-Changing Modes with Speed, Brightness, Play/Pause and ON/OFF controls
  • Maximum load is 4 Amps per channel
  • 12 Amps total
Enter Quantity:
LDRF-RGB4-A RGB Controller w/ RF Remote and Audio
$ 44.95
  • Universal Red/Green/Blue (RGB) LED Controller & Dimmer with handheld RF Remote can control any 12VDC RGB LED products except the RGB-2
  • includes handheld RF wireless remote control which can select 1 of 7 Static Modes or 1 or 4 Dynamic Color-Changing Modes with Speed and ON/OFF controls
  • Maximum load is 4 Amps per channel
  • 12 Amps total
  • Built-in microphone with sensitivity knob or Line-Level audio input jack can be used to trigger color change
Enter Quantity:
LDIR-RGB4 RGB Controller w/Remote
$ 34.95
  • Universal Red/Green/Blue (RGB) LED Controller & Dimmer with handheld Infrared Remote can control any 12VDC RGB LED products except the RGB-2
  • 7 Static Modes or 4 Dynamic Color-Changing Modes with Speed and ON/OFF controls
  • maximum load is 4 Amps per channel
  • 12 Amps total
Enter Quantity:
RGB-CA12 Controller with RF Remote
$ 39.95
  • Universal Red/Green/Blue (RGB) LED Controller with handheld RF Remote can control any 12VDC RGB LED products except the RGB-2
  • includes handheld RF wireless remote control which can select 1 of 7 Static Modes or 1 or 4 Dynamic Color-Changing Modes with Speed and ON/OFF controls
  • Can drive up to 15 meters of our xFLS-RGB Light Strips, for longer runs us our Model RGB-AMP RGB Amplifier below
  • Powered by 12VDC CPS series power supplies sold below
Enter Quantity:
RGB-AMP-DI Amplifier
$ 19.95
  • The RGB-AMP-DI is used to increase load capability for the RGB-CA12 and LDIR-RGB4, one is needed for each additional 22.5 meters of FLS-RGB Light Strips and should only be used after 22.5 meters of FLS-RGB - Powered by 12VDC CPS series power supplies sold below
  • Closeout Item
Enter Quantity:
RGB-WA4 Waterproof Amplifier
$ 19.95
  • Waterproof RGB Amplifer is used to increase load capability for the RGB-CA12 and LDIR-RGB4, one is needed for each additional 30 meters of FLS-RGB Light Strips and should only be used after 30 meters of FLS-RGB
Enter Quantity:
LDK-RGB3 Three Color RGB LED Dimmer
$ 24.95
  • Universal Red/Green/Blue (RGB) LED dimmer can dim any 12VDC RGB LED products from 0 to 100% using Pulse Width Modulation (PWM) circuits
  • Knob controls for full range custom color creation
  • maximum load is 3 Amps per channel
Enter Quantity:
RGB-DC83 Dream-Color Controller
$ 49.95
  • Controller is designed to be used with the SWDC-RGB160 Flexible Light Strips
  • Controls the sequence mode, chase length, and speed of 83 different dynamic chasing patterns from the RF Remote Controller or directly on the RGB Controller unit
  • Chase patters can be paused for static single and multi color effects
  • Includes 12VDC Power Supply for Controller, RF Remote and battery
Enter Quantity:
SWDC-RGB160 Dream-Color Flexible LED Strip
$ 159.95
  • Silicone Encased Waterproof Flexible Light Strip 5 Meter (16.45ft)long with 160 High Power SMD RGB LEDs
  • 5 VDC Operation - Use WPS-5VDC Power Supplies
  • For use with RGB-DC83 Controller only
  • 1/2 meter long 5 conductor signal and power wires
  • see Mounting Brackets and 5VDC power supplies below
Enter Quantity:
SWDC-MC Mounting Clip
$ 0.10
  • Silicone Mounting clips for SWDC series Dream Color Waterproof Flexible Light Strip seen above
  • Attach using 0.09 in. diameter screw holes
Enter Quantity:
5VDC Waterproof Power Supply
$ 12.95
  • Regulated Switching Power Supplies for SWDC-RGB160 5VDC Flexible Light Strips
  • 120VAC Input, 5VDC Output, completely sealed (IP67 rating) with aluminum housing
  • All input and output wires have stripped tinned leads
  • Order Power Cord below if not wiring direct
Enter Quantity:
WFLB-x24 Flexible Light Bar
$ 6.95
  • 9 1/4" Waterproof Flexible Light Bar with 24 Wide Viewing Angle LEDs
  • 12 VDC Operation
  • Completely rubber encapsulated and will conform to most shapes
  • Each Bar includes 3 mounting brackets
Enter Quantity:
WFLB-x96 Flexible Light Bar
$ 16.95
  • 38" Waterproof Flexible Light Bar with 96 Wide Viewing Angle LEDs
  • 12 VDC, Completely rubber encapsulated
  • Highly flexible and will conform to most shapes
  • Mounting brackets sold below
Enter Quantity:
WFLB-x96 Mounting Clips
$ 0.15
  • Plastic Mounting clips for 38" Waterproof Flexible Light Bar seen above
  • Attach using 0.093 in. diameter screw holes and or foam tape sold below
Enter Quantity:
FLB30 series Flexible Light Bar
$ 9.95
  • 19.75 Inch Light Bar with 30 Wide Viewing Angle LEDs
  • 12 VDC Operation, Bars can be cut into 3-LED segments
  • LED aim off the edge of the highly flexible board, with 0.75 inch minimum radius, bars will conform to most shapes
  • see optional FLB-MC mounting clips and Interconnect Jumpers below
Enter Quantity:
FLB30 series Light Bar Jumpers
$ 0.45
  • Four inch Interconnect Jumper for connecting FLB30 series Flexible Light Bars together
  • Six inch Power Jumper for connecting FLB30 series Flexible Light Bars to 12 Volt power source
  • These do not fit FLB18 series
Enter Quantity:
FLB18 series Flexible Light Bar
$ 6.95
  • 12 Inch Light Bar with 18 Wide Viewing Angle LEDs
  • 12 VDC Operation
  • Bars can be cut into 3-LED segments
  • LED aim off the edge of the highly flexible board, with 0.75 inch minimum radius, bars will conform to most shapes
  • see optional FLB-MC mounting clips below
  • Each Bar includes one 6 inch Interconnect Jumper
  • Closeout Item
Enter Quantity:
FLB-MC Mounting Clip
$ 0.25
  • Plastic Mounting Clips for FLB18 and FLB30 series Flexible Light Bar or SNFLS series Side Emitting Flexible Light Strip
  • Attach with included screw holes or foam tape sold below
Enter Quantity:
LB1 series LED Light Bar
$ 12.95
  • 12 Inch Light Bar with 12 High Flux 90 Degree LEDs
  • 12 VDC Operation
  • Bars seperate in 3 inch sections
  • See C21 Jumpers, Mounting Tracks and Power Supplies below
Enter Quantity:
C21 Connectors for LB1 & RLBN Light Bars
$ 0.45
  • Interconnect Jumpers for connecting RLBN series Light Bars or LB1 Light Bar segments
  • Power Jumpers and CPS adapter for connecting Light Bars to 12 Volt power source
Enter Quantity:
Light Bar Mounting Track
$ 0.45
  • Plastic Mounting Track for Light Bars
  • Two minimum required per 12 inch Light Bar, one required per 3 inch LB1 Bar segment
  • Tracks measure 0.95" wide x 1.96" long
Enter Quantity:
Double-Sided Foam Pad 3M-FTP
$ 0.25
  • Closed-Cell Acrylic Foam Tape
  • 3M foam tape pad has high performance adhesive on both sides for attaching Light Bars to a wide variaty of surfaces
  • Price is for each piece, which measures 1.25 x 0.625 inches, 0.088 thick
Enter Quantity:
Double-Sided Foam Tape Strip 3M-FTS
$ 14.95
  • 72 yard reel of Double Coated Polyethylene Foam Tape Strip
  • 3M foam tape strip has high performance adhesive on both sides for attaching linear lighting to a wide variety of surfaces
  • Price is for each 72 yard reel, which measures 1/4in wide x 216ft long
Enter Quantity:
LB2 series LED Light Bar
$ 8.49
  • 12 Inch Light Bar with 12 High Flux 50 Degree LEDs
  • 12 VDC Operation
  • Available in White, Blue, Green, Red, and Amber
  • See LB2 Jumpers and Power Supplies, Mounting Tracks and Tape
Enter Quantity:
LB2 series Light Bar Jumpers
$ 0.45
  • Six inch Interconnect Jumper for connecting LB2 series Light Bars together
  • Six inch Power Jumper for connecting LB2 series Light Bars to 12 Volt power source
Enter Quantity:
RGB-1 Light Bar
$ 24.95
  • Red/Green/Blue Color Changing Light Bars
  • 12 inches long with 36 LEDs
  • Slowly cycles through Red, Green, Blue and many combinations of them
  • Requires RGB Controller for up to 10 RGB Light Bars (includes one Interconnect Jumper)
Enter Quantity:
RGB-1 Controller
$ 14.95
  • Controller for RGB Light Bars
  • 12 VDC operation
  • will drive up to 10 RGB Light Bars
  • includes power jumper
  • Cylces through colors automatically
  • user has no control (see RGB-2 for controllable system)
Enter Quantity:
RGB-2 Controllable Light Bar
$ 24.95
  • Red/Green/Blue Color Changing Light Bar
  • 12 inches long with 36 LEDs
  • Can turn on Red, Green, Blue and many combinations of them
  • Requires RGB-2 Controller for up to 200 RGB-2 Light Bars (includes one Interconnect Jumper)
  • Will NOT work with RGB-CONW
Enter Quantity:
RGB-2 Controller with IR Remote
$ 27.95
  • Controller for RGB-2 Light Bars
  • 12 VDC operation
  • will control up to 200 RGB-2 Light Bars
  • Handheld IR Remote selects pattern, adjusts pattern cycle speed, powers system on/off and remembers last setting when power is cycled
Enter Quantity:
LB3 series LED Light Bar
$ 3.95
  • Light Bar with 6 High Flux 60 Degree LEDs
  • 10~14.5 VDC Operation
  • Bars are 4.32 inch long and included is 5 inch long Interconnect Jumper and Mounting Track with double sided adhesive
  • Closeout Item
Enter Quantity:
LB4 series LED Light Bar
$ 2.95
  • Light Bar with 6 High Flux 60 Degree LEDs
  • 10~14.5 VDC Operation
  • Bars are 7.3 inch long
  • See 5 inch long Interconnect Jumper and adhesive backed Plastic Mounting Track
Enter Quantity:
LB4-I05 Interconnect Jumper
$ 0.45
  • Five inch Interconnect Jumper for connecting LB4 series Light Bars and segments together
  • Also can be cut in half to make 2 Power Jumpers
Enter Quantity:
LB4-MC Mounting Track
$ 0.25
  • Plastic Mounting Track for LB4 series Light Bars
  • Mount by adhesive backing or two screw holes spaced 0.9" apart
  • Tracks measure 1.25" wide x .89" long
Enter Quantity:
LSM series SMD LED Sign Module
$ 4.95
  • Weatherproof LED Sign Module with 3 high power 120 degree 3 chip 5050 SMD LEDs
  • Injection molding PVC housing measures 2.8 x 0.5 inches and have 3.8 inch wires between modules
  • THIS IS OUR BRIGHTEST LED MODULE
  • The quantity you order will be wired together in a string, 50pcs maximum per string
  • 1/8" Mounting hole and 3M double sided adhesive
  • Price is per 3-LED module
Enter Quantity:
LBM2 series LED Module
$ 1.45
  • Waterproof LED Module with 2 high flux 110 degree LEDs
  • measure 1.33 x 1.13 inches and have 3 1/4 inch wires between modules
  • The quantity you order will be wired together in a string, 100pcs maximum per string, price is per 2-LED module

Enter Quantity:
LBM-x2-LP LED Module
$ 1.95
  • Low Profile LED Module with 2 SMD 140 degree LEDs
  • measure 1.36 x 0.73 inches and have 2 1/2 inch wires between modules
  • 1/4 inch thick
  • The quantity you order will be wired together in a string, 20pcs maximum per string, price is per 2-LED module
Enter Quantity:
LBM4 series LED Module
$ 1.95
  • Waterproof LED Module with 4 high flux 60 degree LEDs
  • measure 1.38 x 1.15 inches and have 3 inch wires between modules
  • The quantity you order will be wired together in a string, 50pcs maximum per string, price is per 4-LED module
  • Closeout Item
Enter Quantity:
LBM-x4 LED Module
$ 2.95
  • Waterproof LED Module with 4 high flux 90 degree LEDs
  • measure 1.38 x 1.15 inches and have 3 inch wires between modules
  • The quantity you order will be wired together in a string, 100pcs maximum per string, price is per 4-LED module
Enter Quantity:
LBM-x3SMD series LED Module
$ 3.95
  • Waterproof LED Module with 3 high power 140 degree SMD LEDs
  • Stainless Steel housings measure 1.5 x 1.5 inches and have 3 inch wires between modules
  • The quantity you order will be wired together in a string, 20pcs maximum per string
  • Center mounting hole and 3M double sided adhesive
  • Price is per 3-LED module
Enter Quantity:
LBM1W series LED Modules
$ 12.95
  • Waterproof LED Module with 1 High Power Luxeon 120 degree LEDs
  • measure 1.18 x 1.88 inches and have 2.9 inch wires between modules
  • The quantity you order will be wired together in a string, 51pcs maximum per string, price is per 3 modules
  • Closeout Item
Enter Quantity:
MCM series Accent Light Module
$ 9.95
  • Accent Light with 6 Super Bright LEDs
  • 12VDC Sealed units can be used for low or accent lighting applications
  • Measures 3.375 x 0.75 inches, 6" power leads and grounded mounting hole
Enter Quantity:
Accent Light String
$ 7.95
  • LED Accent Light string
  • 12VDC Units consist of 8 modules with 2 LEDs per module
  • Sealed Modules are are seperated by 3 inches of wire and have a double sided tape backing (3M VHB Tape)
  • Module to module length is 28 inches, overall length is 39 inches
Enter Quantity:
LDP-2A Single Color LED Dimmer
$ 9.95
  • Universal single color LED dimmer can dim any 12VDC LED products from 0 to 100% using Pulse Width Modulation (PWM) circuit knob control
  • maximum load is 2Amps, has male and female 5.5mm barrel power connector for connecting in-line with our CPS series Power Supplies
Enter Quantity:
LDK-8A Single Color LED Dimmer
$ 14.95
  • Universal single color LED dimmer can dim any 12VDC LED products from 0 to 100% using Pulse Width Modulation (PWM) circuit knob control
  • maximum load is 8Amps, screw terminal connect for power in and out connections
Enter Quantity:
LDB-8A Single Color LED Dimmer
$ 14.95
  • Universal single color LED dimmer can dim any 12VDC LED products from 0 to 100% using Pulse Width Modulation (PWM) circuit push button control from stepped intensity adjustment
  • maximum load is 8Amps
  • spring terminal connectors for power in and out connections
Enter Quantity:
LDRF-8A LED Dimmer w/RF Remote
$ 19.95
  • Universal single color LED dimmer can dim any 12VDC LED products from 0 to 100% using Pulse Width Modulation (PWM) circuit push button control for stepped intensity adjustment on Radio Frequency (RF) remote control
  • maximum load is 8Amps
  • spring terminal connectors for power in and out connections
Enter Quantity:
LDR-2A Universal LED Dimmer
$ 39.95
  • Dimmer for LED Light Bars or other 12VDC LED products
  • 2 Amp maximum load, screw terminals for input and output
  • Dimming level is adjusted by built-in slider control or optional remote knob available below
  • Optional mounting plates also available below
  • Measures 3.55 x 2.15 x 1.30 inches
Enter Quantity:
Options for LDR-2A Dimmer
$ 4.95
  • Aluminum Mounting Plate and Remote Knob Assembly for LDR-2A Universal LED dimmer
  • Mounting plate includes 4 screws for attaching to back of dimmer
  • Remote knob on wall plate can be installed in standard junction box, includes connector and 18 inch wires
Enter Quantity:
12VDC CPS series Power Supply
$ 10.95
  • 12VDC Compact Power Supply
  • Input: 100~240VAC, output: 12VDC @ 0.5 ~ 4.1Amps
  • 4 foot long AC in and DC out cables
  • DC Jack is standard 5.5mm barrel connector
  • See Adapter Cables below to connect specific Light Bar to CPS series power supply
Enter Quantity:
CPS Adapter Cable
$ 2.99
  • Adapter Cables to connect Compact Power Supplies to specific LED products
Enter Quantity:
12VDC Waterproof Power Supply
$ 9.95
  • Regulated Switching Power Supplies
  • 120VAC Input, 12VDC Output, completely sealed (IP67 rating) with aluminum housing
  • All input and output wires have stripped tinned leads
  • Order Power Cord below if not wiring direct
Enter Quantity:
12 Volt DC Power Supply
$ 34.95
  • Enclosed 12 VDC Regulated Switching Power Supply
  • Input (VAC@Hz) 85-264@47-63
  • Certification: UL,TUV,CE
  • Order Power Cord below if not wiring direct
Enter Quantity:
Power Cord for Power Supplies
$ 4.95
  • Standard Grounded Power Cord can be used for plugging our power supplies into standard 115VAC receptacle
  • 18 ga, SJT Type 3 Conductor, 6 foot length
Enter Quantity:


USE THE LINKS BELOW TO CHANGE SHOPPING CATEGORIES

COMPONENT LEDS   CAR BULBS   OTHER BULBS   BA9s BULBS   ACCENT LIGHTING   EDISON BASE & MR16/MR11 BULBS
FLASHLIGHTS   TRUCK/TRAILER LIGHTS   LIGHT BARS/STRIPS   UNDER CABINET/DISPLAY LIGHTS   LANDSCAPE LIGHTING   HOBBY/DIY/MISC


Environment Friendly Products super bright leds logo
© 2002-2010 Super Bright LEDs Inc. St. Louis Missouri, USA